User manual SMEG SA682X

[. . . ] INSTRUCTION MANUAL DISHWASHER Contents 1. Safety and operating instructions __________________________ 26 2. Installation and hook-up _________________________________ 28 2. 1 Water supply connection _____________________________________________________ 28 2. 2 Electrical connection ________________________________________________________ 29 3. Description of the controls _______________________________ 30 3. 1 Front panel ________________________________________________________________ 30 3. 2 Washing programs__________________________________________________________ 32 4. [. . . ] The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF ­ 24-31°dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1. 7 Kg of salt in grains. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening. · When using the dishwasher for the first time, in addition to the salt it is also necessary to add one litre of water to the container. Each time the salt container is refilled, make sure that the cap is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. In the event of this occurring, the warranty will be invalidated. Only use regenerating salt specially formulated for domestic dishwashers. If using salt tablets, do not fill the container completely. Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. When necessary, refill the regenerating salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion. · · · · Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damage the water softening system. 34 User instructions ADJUSTING THE WATER SOFTENING SYSTEM The dishwasher is equipped with an device for the user to adjust the water softening system according to the hardness of the water supply. According to the machine model, the selector which acts on the adjustment may be located: inside the plastic locking ring located on the right-hand side, inside the dishwasher; · inside the water softener, just below the cap. · Both allow for adjustment to 5 settings: WATER HARDNESS TABLE WATER HARDNESS German Degrees (°dH) French Degrees (°dF) 0510 23 30 36 4 9 22 29 35 41 0-7 8 - 15 16 - 37 38 - 50 51 - 60 61 - 70 SETTING Setting N. 5 Contact your local water board for information on the hardness of your water supply. 35 User instructions 4. 2 Using the rinse aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser is on the left, and the rinse aid dispenser is on the right. With the exception of the SOAK program, before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser. The rinse aid, on the other hand, should only be added as required. ADDING THE RINSE AID The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door. · · · · · Open the door. Rotate the container cap anticlockwise by 1/4 of a turn and remove it. Add the rinse aid until the container is full (approximately 140 cc). The optical level indicator on the side of the cap should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light illuminates. Replace the cover and turn it in a clockwise direction. [. . . ] Periodically (once or twice a year) it is advisable to clean the tank and gaskets, using a soft cloth and water to remove any deposits. CLEANING THE WATER INTAKE FILTER The water intake filter A located at the outlet of the water supply tap needs to be cleaned periodically. After having closed the water supply tap, unscrew the end of the water intake hose, remove the filter A and clean it delicately under running water. Reassemble filter A in its seat and carefully screw the water intake hose back into position. CLEANING THE SPRAY ARMS The spray arms can be easily removed for periodic cleaning of the nozzles, to prevent possible clogging. [. . . ]