User manual SMEG SC45MFSG

[. . . ] MANUALE D'USO INSTRUCTION MANUAL NOTICE D'UTILISATION GEBRAUCHSANWEISUNG GEBRUIKSAANWIJZING MANUAL DE USO MANUAL DE UTILIZAO BRUKSANVISNING Table of Contents 1. PRECAUTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DISPOSAL INSTRUCTIONS - OUR ENVIRONMENT POLICY . . . . . . . . . . . 31 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The heating system is not activated immediately in any of these functions, in order to improve operator safety. 36 Instructions for the User 7. 3 First use At first use, or after a power failure, the oven's left hand-display, DSP1, will show a flashing symbol. To start any cooking operation, the current time must be set. 7. 3. 1 Setting the current time To set the current time, turn PT1 to the right and left to increase or decrease the hours. Press it once to move on to setting the minutes. Turn it the right and left to increase or decrease the minutes and press it to set the current time. The symbol will appear on the display, which will stop flashing. 7. 3. 2 Changing the current time It might become necessary to change the current time, for example at the switch from summer to winter time. To do this, starting from the standby setting (see point "7. 2 Operating modes") keep PT1 pressed until the figures on DSP1 flash. Now repeat the operations described in point "7. 3. 1 Setting the current time". 7. 4 Selecting the function In the ON state only, a cooking function can be selected by simply turning PT2 to the right or left. The function selected will change colour to red on DSP3. The preset cooking temperature will be displayed on DSP2. 7. 4. 1 Cooking with preset temperature After selection of the function required, the oven will start the cooking procedure at the preset temperature. Cooking itself is preceeded by a preheating stage, which allows the oven to heat to the cooking temperature more quickly. The symbol flashes on DSP2 to indicate that this stage is in progress. The symbols will light up one at a time, from the bottom up, indicating the rise in the temperature inside the oven. When the preheating stage is over, the and symbols will remain constantly on to indicate that the food can be placed inside the oven. 7. 4. 2 Changing the preset temperature The temperature preset for each function can be changed to suit the user's requirements. At any time while cooking is in progress, turn PT1 in either direction to increase or decrease the cooking temperature by 5 degrees at a time. PT1 can also be held in the left or right position to increase or decrease the setting more quickly. 37 Instructions for the User 7. 5 Programmed cooking procedures 7. 5. 1 Cooking with minute minder From ON status (see point "7. 2 Operating modes"), press PT1 once. The display will show the figures (constantly on) and the symbol (flashing). When the symbol is steady and cooking is in progress, press PT1 once. The symbol starts flashing and PT1 can be turned to change the set duration. [. . . ] Loosen the lens from the lampholder with the help of the appropriate tool. Exchange the bulb. Replace the lens, making sure it fits in the correct position without forcing it. Use only light bulbs approved for ovens (T 300C). 48 Instructions for the Installer 11. 2 Removing the door Open the door completely and insert the pins (supplied) into the holes from the inside. Close the door to an angle of about 45 and lift it off. To reassemble, fit the hinges into their grooves, then lower the door into place and extract the pins. [. . . ]