User manual SMEG SE2645TC

[. . . ] ISTRUZIONI PER L'USO ED IL MONTAGGIO INSTRUCTIONS FOR FITTING AND USE INSTRUCTIONS DE MONTAGE ET D'UTILISATION GEBRUIKS- EN MONTAGE-INSTRUCTIES GEBRAUCHS- UND MONTAGEANWEISUNG INSTRUCCIONES PARA EL USO Y MONTAJE INSTRUKCJA OBSLUGI I MONTAU HASZNÁLATI ÉS BESZERELÉSI UTASÍTÁS Piano di cottura da incasso in vetroceramica con comandi Touch Control Built-in glass ceramic hob with Touch-Control switches Plaque de cuisson vitrocéramique à encaster avec commande Touch-Control Vitrokeramische inbouwkookplaat met Touch-Control-bediening Einbau-Glaskeramikkochfeld mit Touch-Control-Bedienung Encimera de vitrocerámica incorporada con mando Touch Control Kuchenka szklo-ceramiczna z systemem obslugi Touch Control Beépíthet kerámia-üveg fzlap touch-control-kezeléssel 223175 1 You now own a glass ceramic hob with Touch-Control switches. Chapters 2 and 3 of these Operating Instructions contain information on how you can make sure that your hob gives many years of service. These Operating Instructions are for use with several types of hobs. The nameplate on the front of these Instructions will show you which type you have bought. Contents 1. [. . . ] When the pre-set cooking time has finished, the cooking zone switches off automatically and an acoustic signal sounds for two minutes. This can be switched off by pressing any key. If you want to switch the timer off beforehand, press cooking zone key 0 and timer key 4. The minus key 7 can now be used to set the timer 5 to "00", or alternatively this can be done by simultaneously pressing the minus and the plus keys 7/8. The timer can also be used as an egg timer when none of the cooking zones are activated. In this case, no cooking zone should be activated when the timer 4 is being set (the stand-by dot cooking zone § does not light up). Safety switch-off Continuous operation of each individual cooking zone is temporally limited by a safety shut-off which switches off the cooking zone in accordance with the selected cooking level after a specified time interval. The intervention times of this safety device are included in the attached time table. When the safety shut-off has switched off the touch control system, a "0" is shown in the cooking level display ", or an "H" if there is still any residual heat left. Pressing the on/off switch key makes the control system ready for operation again. If more than one key is pressed simultaneously - with the exception of the minus and plus keys - the control system will not accept this as a valid command. If one or more keys are activated for longer than 30 seconds, for example by boiling over or the weight for a pan, the control system assumes that there is an error and switches off automatically. If key operation continues, a constant acoustic signal sounds. Table of times MOT = maximum operating time, in hours MOT (h) 6 6 5 5 4 1. 5 1. 5 1. 5 1. 5 Cooking level 1 2 3 4 5 6 7 8 9 14 223175 2. Things to watch out for 2. 1 Notes on the right types of saucepans Use only pots and pans with bottoms that are firm, even and as thick as possible. This applies particularly to cooking with high temperatures, e. g. Uneven bottoms extend cooking times and increase energy consumption. The best transmission result is obtained when the pots and the cooking zone are of equal dimension. Energy is wasted if you cook without a lid placed correctly on the pan. In order to work directly on the cook zones, you can use cooking utensils made from fireproof glass or porcelain if their bottoms are flat polished. Please heed the manufacturer's instructions. Always take away overflow food. Clean the hob before using it for the first time. Afterwards, switch on the elements to the highest level one after the other, without pots, for three minutes in order to eliminate any odours due to newness or and so that any moisture that may still be in the heating element may evaporate. This is necessary so that the electronic circuits function properly. 2. 2 Important Attention: The surfaces of the heating and hotplate zones become hot during use. [. . . ] 4 for the position of the cable cut-out. Connection options 4. 2 Maintenance and repair work Before repair work is carried out, disconnect the appliance from the mains. If you have to contact our service department, always quote the type and make numbers. You can find these numbers on the nameplate or on page 1 of the Operating Instructions. Each time the glass ceramic hob is removed from the worktop, check the seals and replace if necessary. 4. 3 Working surface cut-out Carry out all cutting out of furniture units and worktops before fitting the appliance, and remove all sawdust and chips. [. . . ]