User manual SMEG SE644ID1

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RECYCLING INSTRUCTIONS - OUR ENVIRONMENT POLICY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BEFORE FIRST USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For simplicity, from now on we will refer to the Touch Control sensor buttons simply as the 'buttons'. On/off button Use this to turn the hob on and off. In effect, this button is the main switch. Cooking zone selection button / Increase button By activating one of the available selectors you select a cooking zone, the power level of which can then be increased using the same button " ". Decrease button This button can be used to reduce the value shown on the display. The " " and " " buttons can be activated with a single touch or held down (again individually) for a period (to modify the value quickly). Cooking level indicator This indicator shows the level selected, i. e. : = the residual heat = rapid start cooking = the Stop function ER03 = Error message When the availability light is on Lock sensors button Used to lock the sensors. , it is possible to set the cooking zone. STOP button The cooking process can be briefly paused using the STOP function. Timer selector Used to increase the cooking time with the automatic switch-off (timer). 39 Instructions for the User 8. USING THE HOB 8. 1 Warnings and general advice To operate a hob equipped with touch controls, lightly press the symbols printed on the surface of the hob. Every pressure on a symbol is confirmed by a control beep. On first connection to the electrical mains, an operating check will be carried out automatically and all the indicator lights will come on for a few seconds. 8. 2 Operating power settings The table below shows the maximum consumption of the hotplates when they are in operation. ZONE NUMBER ZONE DIAMETER 160 mm 200 mm 160 mm 200 mm MAX ABSORBED POWER 1400 W 2300 W 1400 W 2300 W 40 Instructions for the User 8. 3 Switching on the hob and the cooking zone To activate the control described here, after pressing one (selection) button, you need to press another one afterwards. The second button needs to be pressed within 10 seconds, as otherwise the desired selection will be deactivated. 1 Press the on/off button until the power level indicators show "0". 2 Then press a button to select the cooking zone (e. g. The function light for the selected cooking zone will come on. 3 Select the cooking level using the button (selection/increase) or (decrease). By selecting the button, cooking level 1 is activated; by selecting the button, level 9 is activated. 4 Place a metal saucepan on the cooking zone. Saucepan recognition will activate the induction coil. No power is transmitted to the cooking zone until a metal saucepan is placed on it. To cook on other cooking zones at the same time, repeat the steps in points 2 to 4. When applying radiant heat, the cooking utensils must not have magnetic properties (proceed as detailed in points 2 and 3). 8. 4 Switching off the cooking zone 5 The function light for the selected cooking zone must be lit. If necessary, activate the cooking zone selector. 6 a) Press the button until cooking level "0" is shown, or: b) Press the and buttons at the same time. [. . . ] The earthing wire must be longer than the current conduction wires so that, if the plug is torn off the power cable, it is the last to be detached. · Surplus parts of the cable must be taken out of the installation area under the appliance. · To make the connection, the control cover underneath the device must be opened to reach the terminal board. Once the connection has been made, the cover must be fixed back in place and the cable must be locked using a tractionresistant clamp. [. . . ]