User manual SMEG SFP750BS

[. . . ] 8 3. 2 Your environmental care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GET TO KNOW YOUR APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4. 1 Description of the controls on the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVAILABLE ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Using this, foods can be cooked on the rack and the fat can be collected separately. 5. 3 Using the reduction pan stands The reduction pan stands should be placed on top of the hob pan stands as shown in the adjacent figure. The WOK pan stand should only be used when cooking with a wok. 11 Instructions for the user 6. USING THE COOKING HOB 6. 1 General warnings and advice Before lighting the hob burners, make sure that the flame-spreader crowns are correctly positioned in their housings with their respective burner caps. 6. 2 Lighting the hob burners All the appliance's control and monitoring devices are located together on the front panel. The burner controlled by each knob is shown next to the knob. The appliance is equipped with an electronic lighter. Simply press the knob and turn it anti-clockwise to the maximum flame symbol until the burner lights. If the burner does not light in the first 15 seconds, turn the knob to “0” and wait 60 seconds before trying again. After lighting, keep the knob pressed down for a few seconds to allow the thermocouple to heat up. The burner may go out when the knob is released: in this case, the thermocouple has not heated up sufficiently. Wait a few moments and repeat the operation, keeping the knob pressed for longer. If the burners should go out accidentally, a safety device will be tripped, cutting off the gas supply, even if the gas tap is open. In order to avoid this, open the door very carefully a couple of times while cooking. To prevent hazardous overheating, the appliance's lid (where present) must always be raised when using the oven. Heat the empty appliance to the maximum temperature in order to remove any manufacturing residues which could affect the food with unpleasant odours. 14 Instructions for the user 7. 7 Using the bottom burner 7. 7. 1 Electronic spark ignition Open the oven door fully, press the thermostat knob and turn it anti-clockwise between MIN and MAX; the electric spark ignition is activated automatically. After lighting, keep the knob pressed down for a few seconds to allow the thermocouple to heat up. If the burner does not ignite after 15 seconds, stop attempting to light it, leave the oven door open and do not try to light it again for at least 1 minute. The bottom burner cannot be lit with the oven door closed. 7. 7. 2 Manual ignition In the event of a power failure, the oven can be ignited manually. Open the oven door fully, press and turn the thermostat knob anti-clockwise between MIN and MAX; light a long match and put the flame through the centre front slots at the bottom of the oven (as indicated in the figure). Alternatively you can use an electric gas lighter with a long spout. After lighting, keep the knob pressed down for a few seconds to allow the thermocouple to heat up. If the burner does not ignite after 15 seconds, stop attempting to light it, leave the oven door open and do not try to light it again for at least 1 minute. [. . . ] The tightening torque of the screws of the terminal supply wires must be 1. 5 - 2 Nm. The aforementioned power cables are sized taking into account the coincidence factor (in compliance with standard EN 60335-2-6). 26 Instructions for the installer 11. 5 Positioning the skirt (on some models only) The skirt must always be positioned and secured correctly on the appliance. 1 Loosen the 4 screws (A) on the back of the worktop (2 for each side). 2 Place the skirt above the worktop, taking care to align the skirt's slots (B) with the screws (A). [. . . ]