User manual SMEG SG38

[. . . ] It also accumulates heat during the initial operating phase of the resistance allowing, before long, uniform grilling very similar to that obtained using charcoal. For better results it is recommended you pre-heat the lava stone for at least 10 minutes on position 1. This step is strongly recommended when the appliance is switched on for the first time. It reduces the risk of the cooked food absorbing the odours produced by the resistance the first time it is switched on. FIG. [. . . ] Do not touch it with your hands or other objects to avoid burns. - As soon as a crack is noticed on the surface of the heating element, immediately disconnect the appliance from the mains. 16 CLEANING CAUTION: Before cleaning of any kind, disconnect the appliance from the mains. WARNING: - To maintain the grill in good condition after use, it should be treated with the special products available on the market so that the surface always remains clean. This procedure is necessary to prevent the formation of rust. - Don't use steam jets for the equipment cleaning. 2) COOKING SURFACE To maintain the surface of the barbecue always clean and to extend the lifespan of the appliance, it is very important to wash it after every use with warm, soapy water, rinse, and dry thoroughly. Let the barbecue and all its parts cool off before cleaning. Do not use scouring pads, abrasive cleaners or corrosive sprays. Never allow vinegar, coffee, milk, salt water, lemon or tomato juice to remain in contact with the surfaces for long periods of time. 17 INSTALLATION TECHNICAL DATA FOR INSTALLERS Installation and maintenance listed in this section must only be carried out by qualified personnel (law n° 46 and D. P. R. A faulty installation can cause damage to persons, animals or objects, towards whom the manufacturer cannot be held responsible. The cut-off or automatic control devices of the appliance can only be modified by the manufacturer or by a duly authorized supplier. An opening in the table top of the piece of modular furniture must be made with the dimensions indicated in fig. - To connect, do not use adaptors or switches as they may cause false contacts resulting in dangerous overheating. When connection is made directly to the power circuit: - Place a switch between the appliance and the circuit of an appropriate size for the load of the appliance and with a minimum aperture between contacts of 3mm. - Remember that the earth cable must not be broken by the switch. - As an alternative, the electrical connection may also be protected by a high sensitivity differential switch. It is strongly recommended that the yellow-green earth cable provided be connected to a good earth installation. WARNING: All of our appliances are designed and manufactured according to European standards EN 60 335-1 and EN 60 335-2-6 and relative amendments. This appliance satisfies the requirements of European directives: - CEE 89/336 + 92/31 + 93/68 concerning electromagnetic compatibility. - CEE 73/23 + 93/68 concerning electrical safety. FIG. 7 20 MAINTENANCE Before carrying out maintenance of any kind, disconnect the appliance from the mains. All maintenance must be carried out by authorized personnel only. make certain that they are well positioned in the guides along the side of the appliance. [. . . ] Take out the drip pan containing the lava stone and loosen the four screws that are under it (see fig. The work surface can now be detached from the worktop giving access to all internal components. To reassemble the work surface of the appliance take care not to damage the power cables and 7) TECHNICAL SPECIFICATIONS OF ELECTRICAL COMPONENTS To facilitate the task of the installer a table with component specifications is included below. ELECTRICAL COMPONENTS OUTPUT Name Grill W 2400 TYPE AND SECTION OF POWER CABLES Type of cable Rubber H05 RR-F Neoprene H05 RN-F Total output of appliance 2400 W 2400 W Single-phase power supply 230 ­ 240 V ~ 3 X 1. 5 mm2 (*) 3 X 1. 5 mm2 (*) FIG. 9 21 TECHNICAL SPECIFICATIONS BARBECUE Voltage Frequency Total nominal power 230 ­ 240 V ~ 50/60 Hz 2400 W 22 TECHNICAL ASSISTANCE AND SPARE PARTS Before leaving the factory, this equipment was tested and adjusted by skilled personnel so as to guarantee the best operating results. [. . . ]