User manual SMEG SIM562B

[. . . ] All safety messages will be preceded by the danger symbol and the following words: DANGER WARNING Indicates a hazardous situation which, if not avoided, will result in serious injury. Indicates a hazardous situation which, if not avoided, could cause serious injury. All messages relevant to safety specify the potential risk to which they refer and indicate how to reduce the risk of injury, damage and electric shocks due to incorrect use of the appliance. Make sure to comply with the following: - Use protective gloves to perform all unpacking and installation operations. - The appliance must be disconnected from the power supply before carrying out any installation operation. [. . . ] Only use pots bearing the symbol “INDUCTION SYSTEM” (Figure opposite). Place the pot on the required cooking zone before switching the hob on. EXISTING POTS AND PANS OK NO Use a magnet to check if the pot is suitable for the induction hob: pots and pans are unsuitable if not magnetically detectable. - Make sure pots have a smooth bottom, otherwise they could scratch the hob. - Never place hot pots or pans on the surface of the hob’s control panel. This could result in damage. RECOMMENDED POT BOTTOM WIDTHS XL Ø 28 cm 17 cm min. Ø 28 cm max. M Ø 18 cm 12 cm min. Ø 18 cm max. L Ø 21 cm 15 cm min. Ø 21 cm max. S Ø 14. 5 cm 10 cm min. Ø 14. 5 cm max Max. Min. Ø 12 cm Multizone 23 cm 39 cm EN15 INSTALLATION After unpacking the product, check for any damage during transport. In case of problems, contact the dealer or the After-Sales Service. For built-in dimensions and installation instruction, see the pictures in page 2. PREPARING THE CABINET FOR FITTING WARNING - - Install a separator panel under the hob. The lower part of the product must not be accessible after installation. Do not fit the separator panel if an undertop oven is installed. min. 5 mm • • • • • The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure. Connect the appliance to the power supply by means of a multipole switch with minimum contact gap of 3mm. INSTRUCTIONS FOR USE Control Panel Description Control panel Multizone On/Off Multizone Quick access Slider Control panel lock Cooking zone controls and corresponding display Switching the hob ON/OFF To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up. To switch off, press the same button until the displays switch off. All the cooking zones are deactivated If the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled down. If within 10 seconds of switching on, no function is selected, the hob switches off automatically. Switching on and adjusting cooking zones Slider operation Power indicator display Selected cooking zone indication Increase power level Cooking zone positioning Decrease power level After switching the hob on, activate the required cooking zone by pressing the corresponding circular button and place the pot on the zone. With the Slider control it is possible to select the required power level, from min. 9, or booster “P” if available. To increase the power level, slide your finger on the slider from left to right several times; to decrease it, slide in the opposite direction. Alternatively the “+” and “-” quick access buttons can be used. Deactivation of cooking zones To switch off the cooking zone, press the corresponding button for more than 3 seconds. The cooking zone switches off and, if still hot, the letter “H” appears on the zone display. EN17 Control panel lock This function locks the controls to prevent accidental activation of the hob. To activate the control panel lock, switch the hob on and press the Timer button for three seconds; an acoustic signal and a luminous indicator near the padlock symbol signal activation. [. . . ] If the display shows , the cooking zone is still hot. If the residual heat indicator of a given cooking zone is lit, that zone can be used, for example, to keep a dish warm or to melt butter. When the cooking zone cools down, the display goes off. If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions for your induction hob, the message “no pot” will appear in the display (see figure at side). [. . . ]