User manual SMEG SIM570B

[. . . ] 1 DEUTSCH ENGLISH FRANÇAIS NEDERLANDS ESPAÑOL PORTUGUÊS ITALIANO SVENSKA DANSK РУССКИЙ POLSKI Installation Installation Installation Installatie Instalación Instalação Installazione Montering Installation Установка Instalacja Seite 6 Page 15 Page 24 Pagina 33 Página 42 Página 51 Pagina 60 Sidan 69 Side 78 Стр. 87 Strona 96 Bedienungsanleitung Instructions for use Mode d’emploi Gebruiksaanwijzing Instrucciones de uso Instruções de utilização Istruzioni per l’uso Bruksanvisning Brugervejledning Руководство по эксплуатации Instrukcja obsługi Seite Page Page Pagina Página Página Pagina Sidan Side Стр Strona 8 17 26 35 44 53 62 71 80 89 98 ۳ 2 ٥ A 52 mm 560 +2 mm 0 R = Min. 50 mm 580 650 700 mm 510 mm 490 +2 mm 0 30 483 mm 553 mm +1 0 mm 2 Min. 5 mm 1 2 X4 3 3 IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT This manual and the appliance itself provide important safety messages, to be read and always observed. [. . . ] The lower part of the product must not be accessible after installation. Do not fit the separator panel if an undertop oven is installed. min. 5 mm • • • • • • The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure. In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. If an undertop oven is installed, make sure the oven is equipped with a cooling system. Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them. In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit 4801 211 00112. To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of the appliance. EN15 ELECTRICAL CONNECTION Disconnect the appliance from the power supply. Installation must be carried out by qualified personnel who know the current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home. WARNING - - Connect to terminal Block For the electrical connection a power cord ( 5x2. 5 mm ) is present in the supply. To connect to the terminal block, follow the instuction below: L1=R BLACK        L2=S BROWN     =E YELLOW-GREEN N1=N BLUE         N2=N GREY with blue film Remove shunts from terminal block Before power cord connection remove the two shunts as per picture Connecting to the terminal block • • • Secure the power cable with the cable clamp. Remove the terminal cover (A) by unscrewing the screw and insert the cover into the hinge (B) of the terminal. Close the cover (C) and screw on the terminal with the screw removed. Connect to wall side For 220-240V 1N use the cord paired as supplied. For 380-415V 3N or 380-415V 2N, separate with the scissors the wires as showed in the image below and connect them. EN16 INSTRUCTIONS FOR USE Control Panel Description Control panel “Flexicook model” (when available) On/Off Quick access Slider Control panel lock Power management/Timer/ Lock function button Cooking zone controls and corresponding display Switching the hob ON/OFF To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up. To switch off, press the same button until the displays switch off. If the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled down. If within 10 seconds of switching on, no function is selected, the hob switches off automatically. Switching on and adjusting cooking zones Slider operation Power indicator display Selected cooking zone indication Increase power level Cooking zone positioning Decrease power level After switching the hob on, activate the required cooking zone by pressing the corresponding circular button and place the pot on the zone. With the Slider control it is possible to select the required power level, from min. 9, or booster “P” if available. [. . . ] Place the pot in the center of the single zone and adjust the power level with the slide touchscreen. remains visible on the display to remind that the zone i The message “no pot” i Important: make sure to place the pans centered on the cooking zone in the way to cover the center of the single cooking zone. In case of big pot, oval, rectangular and elongated pans make sure to place the pans centered on the cooking zone. Examples of good pot placement and bad pot placement : EN19 CLEANING WARNING Do not use steam cleaners. Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H”) is not displayed. IMPORTANT: Do not use abrasive sponges or scouring pads. [. . . ]