User manual SMEG SIM581B

[. . . ] 50 mm 0 R = 11, 5 mm 0 483 mm 742 mm 490+2 mm 0 0 513 +2 750+2 mm mm R = 11, 5 mm 6 mm R = Min. 5 mm 1 2 3 4 ENGLISH Installation Page 2 Instructions for use Page IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT This manual and the appliance itself provide important safety messages, to be read and always observed. This is the danger symbol, regarding safety, warning of potential risks to users and others. All safety messages will be preceded by the danger symbol and the following words: DANGER WARNING Indicates a hazardous situation which, if not avoided, will result in serious injury. [. . . ] Cut the worktop to fit before installing the hob and carefully remove any shavings or sawdust. If an oven is installed beneath the hob, make sure that it is equipped with a cooling system. To remove the hob from the worktop use a screw driver (not supplied) unlocking the springs from the bottom side of the appliance. Do not install the hob above a dishwasher or washing machine, to prevent the electronic circuits from coming into contact with steam or moisture and being damaged as a result. WARNING - • • • • • • ELECTRICAL CONNECTION Disconnect the appliance from the mains power supply. The appliance must be installed by a qualified technician who is fully aware of current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power supply cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the appliance rating plate is the same as that of the domestic power supply voltage. Do not use extension cables. WARNING - - Connecting to the terminal board The hob is provided with a pentapolar cable 5x2. 5 mm2, suitable for the connection 400 V 3N ~. For electrical connection, use the cable supplied or an H05RR-F cable as specified in the table below. Conductors 220-240 V ~ + 220-240 V 3 ~ + 380-415 V 3N ~ + 380-415 V 2N ~ + Amount x size 3 x 4 mm2 4 X 1. 5 mm2 5 X 1. 5 mm2 4 X 1. 5 mm2 380-415 V 3N ~ 220-240 V ~ min 5 mm 220-240 V ~ (UK - AU) 230 V 230 V 230 V 230 V A B C 380-415 V 2N ~ 220-240 V 3 ~ (Belgium only) 380-415 V 2N ~ (NL only) 230 V 230 V 230 V 230 V Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. The cooking zone switches off and, if the zone is still hot, the letter “H” appears in the square. “H” is the residual heat indicator. The hob is fitted with a residual heat indicator for each cooking zone; these indicators alert the user when cooking zones are still hot. When the cooking zone cools down, the display switches off. EN18 Timer selection The timer can be used to set a max. Select the cooking zone to be used with the timer (a dot lights up at the bottom right of the power level indicator), then set the required cooking time using the + and - keys of the timer function: the time in minutes is shown next to the cooking zone display. To switch the cooking zone off, press OFF will appear on the display of the zone that is not able to detect any pot (because of missing pot, or misplaced or not suitable for induction hob). This message remains active for 60 seconds: in this time you can add or slide pots within the Multizone as you prefer. After 60 seconds if no pan is placed on the zone, the system stops “searching” pots on that zone, the symbol remains visible on the display to remind that the zone is disabled. To reactivate the Multizone function on both heaters, press the button . The Multizone function is also able to detect when a pot is moved from one zone to the other one within the Multizone keeping the same power level of the zone where the pan originally was placed (see the example in the figure below: if the pot is moved from the front heater to the rear heater, the power level will be shown on the display corresponding to the zone where the pot is placed). i The message “no pot” It is also possible to operate the Multizone as two independent cooking zones, using the corresponding button of the single zone. [. . . ] • Use a soft cloth, absorbent kitchen wipes or a specific hob cleaner (follow the Manufacturer’s instructions). TROUBLESHOOTING GUIDE • • • • • Read and follow the instructions given in the section “Instructions for use”. Check that the electricity supply has not been shut off. If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions. If you are unable to turn the hob off after using it, disconnect it from the power supply. [. . . ]