User manual SMEG SLB1601EX

[. . . ] 49 AVAILABLE ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 USING THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 COOKING WITH THE OVEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Modifying the set data Once the countdown has started it is possible to change its duration during cooking. starts flashing and PT1 can be will turned to change the set duration. A few seconds after the last change, stop flashing and the countdown will restart from the new value. To change the preset temperature, wait for to become steady and turn PT1 to the right or left to increase or decrease the cooking temperature. 61 Instructions for the user 7. 7. 2 Semi-automatic cooking Semi-automatic cooking is the function which allows a cooking operation to be started and then ended after a specific length of time set by the user. Select a cooking function (see "7. 6 Selecting functions (pyrolytic models)") and press PT1 twice. The display will show and (flashing). Turn PT1 to the right or left to set the minutes of cooking (from 00:01 to 23:59). A few seconds after the desired duration is set, will stop flashing and semi- automatic cooking will start from that moment. At the end, the word STOP will appear on DSP1, cooking will stop and a buzzer will sound; press PT1 once to deactivate it. If you wish to continue cooking beyond the set time, press PT1 again. The oven will restart normal operation with the cooking settings selected previously. Turn PT2 to "0" to switch off the oven completely. Cooking is preceded by a pre-heating phase (common to all functions) which allows the oven to reach the cooking temperature more quickly. This phase is indicated by pre-heating phase, flashing on the display (DSP1). At the end of the will remain constantly on to indicate that the food can be placed inside the oven. 7. 7. 4 Changing the preset temperature The preset temperature for each function can be changed to suit the user's requirements. At any time while cooking is in progress, turn PT1 in either direction to increase or decrease the cooking temperature by 5 degrees at a time. PT1 can also be held in the left or right position to increase or decrease the setting more quickly. 64 Instructions for the user 7. 8 Secondary menu (pyrolytic models) The secondary menu appears on first use, after a power failure or by holding PT1 down for 3 seconds with the oven set to OFF (see "7. 4 Operating modes (pyrolytic models)"). The secondary menu enables the user to: Set the time shown on the display (DSP1). 1 P1: OFF / ON Activate or deactivate the child safety lock ( ); this function, after 2 minutes of operation without any actions by the user, locks all the functions and knobs; it is identified by the appearance of on DSP1. To temporarily deactivate locking and modify a cooking programme or select a different function, keep PT1 pressed down until disappears from DSP1. At this point you can make the desired changes, and 2 minutes after the last setting, the lock will be reactivated. To permanently deactivate the lock, you have to enter the secondary menu and deactivate it as described in this paragraph. 2 P2: OFF / ON Activate or deactivate the Show Room function; this function disables all the heating elements so that only the control panel works (to use the oven normally, set P2:OFF). 3 P3: OFF / ON Activate or deactivate the function that allows a maximum consumption of 2300 W. When the child safety lock is activated (P1:ON), if a knob is moved , "bLOC" is displayed on DSP1 for 2 seconds. [. . . ] This operation may have to be repeated during the glass removal process if the door is accidentally freed. 81 Instructions for the installer Removing the internal glass panel: · Remove the internal glass panel by pulling it upwards, following the movement indicated by the arrows. Doing this detaches the 4 pins attached to the glass from their slots in the oven door. Removing the middle glass panels: (pyrolytic models) · There are two middle glass panels in pyrolytic models, attached using 4 small locks. Remove the middle panes by lifting them upwards. (Multifunction models) · Multifunction models have a single middle panel. [. . . ]