User manual SMEG SNZ414S

[. . . ] INSTRUCTION MANUAL DISHWASHER Contents 1. 6. Safety and operating instructions __________________________ 4 Installation and hook-up _________________________________ 7 Description of the controls________________________________ 10 Operating instructions ___________________________________ 19 Cleaning and maintenance _______________________________ 27 Troubleshooting _______________________________________ 31 Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. The manual is divided into paragraphs, which provide a step by step description of the dishwasher functions, with clear instructions accompanied by detailed illustrations. [. . . ] If the program you wish to carry out is the same as the one already in progress: press the START/PAUSE button (4) for a few seconds, until the PHASES/PROGRAM lights (8) come on; annul the program in progress (see relative section) and wait for the cycle to come to an end; select the program again; select the delay required; press the START/PAUSE button (4) to start the new program. If the program you wish to carry out is different from the one already in progress: press the START/PAUSE button (4) for a few seconds, until the PHASES/PROGRAM lights (8) come on; change the program; select the delay required; press the START/PAUSE button (4) to start the new program. The dishwahser will pump out the water and restart with the delay set and the new program. 5 6 7 8 9 1 2 10 3 4 17 User instructions TO SAVE ON ENERGY!AND PROTECT THE ENVIRONMENT Always try to run the dishwasher fully loaded. Do not wash the dishes in running water. Use the washing program that is most appropriate for each type of load. Do not carry out any preliminary rinsing. If available, connect the dishwasher to a hot water supply up to 60C. When possible, skip the drying cycle by leaving the door open when the washing cycle is complete; the air and the residual heat will dry the dishes perfectly. TO CUT DOWN ON DETERGENT CONSUMPTION!AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following: separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; do not pour the detergent directly on the dishes. REMOVING THE DISHES At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket. 18 User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: Add the rinse aid and detergent. 4. 1 Using the rinse aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser is on the left, and the rinse aid dispenser is on the right. With the exception of the SOAK program, before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser. The rinse aid, on the other hand, should only be added as required. ADDING THE RINSE AID The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door. Rotate the container cap anticlockwise by of a turn and remove it. Add the rinse aid until the container is full (approximately 140 cc). The optical level indicator on the side of the cap should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light illuminates. Replace the cover and turn it in a clockwise direction. Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam. 19 User instructions ADJUSTING THE RINSE AID DISPENSER SETTING The dishwasher is factory set for medium water hardness. However it possible to change the setting by turning the dispenser's selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position. The setting must be increased when the washed dishes appear dull or have circular staining. To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it. [. . . ] It is essential to thoroughly clean the filters according to the above instructions: the dishwasher cannot function if the filters are clogged. Carefully replace the filters in their seats, to avoid damaging the wash pump. PROLONGED DISUSE: Run the soak program twice in succession. Leave the door slightly open, in order to prevent the formation of unpleasant odours inside the washing tank. Shut off the water supply tap. BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE: Check that there are no deposits of sludge or rust inside the water pipe: if there are, allow the water to run from the water supply tap for a few minutes. [. . . ]