User manual SMEG SP34W

[. . . ] THE POSITIONING, CONNECTIONS, SETUP AND TROUBLESHOOTING, AND THE SUBSTITUTION OF THE POWER CABLE MUST BE PERFORMED BY QUALIFIED PERSONNEL. THE DISHWASHER IS INTENDED EXCLUSIVELY FOR PROFESSIONAL USE AND MUST BE USED BY COMPETENT PERSONNEL. IT IS DESIGNED TO WASH DISHES (PLATES, CUPS, BOWLS, BAKING PANS, SILVERWARE) AND SIMILAR ITEMS FROM THE GASTRONOMY AND THE COLLECTIVE RESTAURANT INDUSTRIES. IT CONFORMS TO THE INTERNATIONAL ELECTRIC AND MECHANICAL SAFETY NORMS (CEI-EN-IEC 60335-2-58/61770) AND ELECTROMAGNETIC COMPATIBILITY NORMS (CEI-IEC-EN 55014-1/-2, 61000-3;4, 50366). [. . . ] To empty the Tank first remove the Tank's overflow, then press the button for 3 seconds. This inhibits water from being loaded and, after a Pressostat Tank-empty signal verifies that the Tank has been emptied, will only allow a limited amount of boiler water to circulate in order to facilitate the cleaning of the Tank. Tank emptying button At the end of the function the machine goes into a stand-by phase which is indicated by the appearance of three dashes "---" upon the displays. To render the machine operational again it is therefore necessary to insert the Tank's overflow and to press the button. If the machine is equipped with the drain pump option, the drain pump will also be activated. IN PARAMETERIZATION MODE, IF NO BUTTON IS PRESSED WITHIN 30 SECONDS THE KEYBOARD SHUTS DOWN AND RETURNS TO ITS OFF STATE. 8 Regeneration mode: Once having reached the set number of cycles, at the end of the last cycle (ex. The 20th or the 35th, etc. ) the message rig will appear flashing on the display for 10"; of it is desired to continue and the request is ignored, the message will appear for 10" at the end of every cycle. The regeneration phase only begins after the Tank Pressostat has arrived at empty 1) EVR active for 20", 1' break ­ repeat EV regenerate activation 4 times 2) 8' break 3) EV1 active for 25", 1' break - repeat EV load activation 4 times, PS activation (drain pump) contextually to EV load + 5" Afterwards, once the first samples are available, verify the correctness of the times/actual regeneration and proper resin washing. At the end of the regeneration, the display goes back to showing the last program performed and the machine is once again ready for use. Note: the regeneration cycle can be cancelled once initiated by keeping the button pressed for 10 seconds. 7 SCREEN DISPLAYED ANOMALIES After having turned the machine off and on again, if the problem persists communicate the type of error displayed on the screen to technical assistance: E1 E2 E3 E6 E7 E8 Boiler sensor malfunction Tank sensor malfunction Water loading timeout ( the water loading duration has exceeded the set time ) Draining anomaly. At the end of the draining phase the CPU still detects water in the Tank. The drain led indicator will flash until draining has been completed. 12 Once draining has been completed the machine goes into standby, indicated by the appearance of dashes "--" upon the display. The pressing and afterwards press the regeneration cycle starts and moving dashes appear on the display; after 20 minutes the regeneration cycle ends and the machine goes into standby. Open the door, insert the overflow into the Tank and turn off the main wall switch. During the execution of the regeneration cycle it will not be possible to perform any operations. It must always be done with the Tank empty. Refilling the supply of regenerating salt (for models equipped with water softeners) ). The refill is to be performed once the insufficient salt indicator appears on the display ( Perform the salt refill when there is no water in the Tank in order to keep wash water from entering the water softener device. The salt tank has a capacity of about 1 kg of granulated salt. The tank is situated at the bottom of the Tank. After having extracted the basket, unscrew the cap and pour the salt through the provided funnel. Before screwing the cap back in place remove any eventual salt residues in proximity to the opening. 8. 5 Total drainage at the end of the day The dishwasher is capable of performing an auto-clean cycle at the end of the day. [. . . ] Rinse and dry with care. 10. 3 Prolonged disuse If the use of the dishwasher is not foreseen for a relatively long period of time it is necessary to drain the detergent and rinse-aid dispenser in order to avoid crystallization and pump damage: Remove the suction tubes from the detergent and rinse-aid containers and emerge them in a container filled with clean water. Perform a few wash cycles and drain the machine completely. Finally, turn off the main switch and close the water supply faucet. The detergent and rinse-aid suction tubes will be placed back in the containers when the machine is ready to be put back in use, taking care so as not to invert the tubes (red tube = detergent; transparent tube = rinse-aid). [. . . ]