User manual SMEG SPR876RAGH

[. . . ] 30 MANUTENO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2 2 RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. [. . . ] Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 3 3 CHARACTERISTICS Dimensions Min 780 700 Max 1070 132 90 Min. 500mm 650mm 310 70 350 150 650 290 36 EN 4 4 Components Ref. 1 2 2. 1 2. 2 7. 1 7. 1a 7. 1b 8a 8b 9 10 14. 1 15 24 25 26 27 Ref. 11 12c 12e 12f 12g 12h 12q 21 22 23 Q. ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 Q. ty 4 6 2 2 4 4 4 1 8 4 Product Components Hood Canopy complete with: Controls, Lights, Filters Telescopic chimney made up of: Upper chimney Lower chimney Telescopic frame complete with Suction fan, made up of: Upper frame Lower frame Rh Air Outlet Directional Grille Lh Air Outlet Directional Grille Reduction flange 150-120 mm Dumper Air Outlet Connector Extension Air Outlet Connector Connection box Pipe clamps (not included) Cable clamps Finishing plug Installation Components Wall Plugs 10 Screws 2, 9 x 6, 5 Screws 2, 9 x 9, 5 Screws M4 x 80 Screws M6 x 80 Screws 5, 2 x 70 Screws 3, 5 x 9, 5 Drilling template 6. 4 mm int. dia washers M6 nuts 21 23 22 11 12h 7. 1a 12g 7. 1 14. 1 10 7. 1b 12c 2. 1 2 2. 2 8b 8a 12e 24 9 25 26 27 15 12c 1 12c 12f 22 12q Q. ty Documentation 1 Instruction booklet EN 5 5 INSTALLATION Drilling the Ceiling/shelf and fixing the frame DRILLING THE CEILING/SHELF ?Use a plumb line to mark the centre of the hob on the ceiling/support shelf. Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template is in the correct position by lining up the axes of the template with those of the hob. Mark the centres of the holes in the template. In all cases where the ceiling is not strong enough at the suspension point, the installer must provide strengthening using suitable plates and backing pieces anchored to the structurally sound parts. 1 1 2 2 Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe 150 or 120mm, the choice of which is left to the installer. Fix the pipe in position using sufficient pipe clamps (not supplied). To install a 120 mm air exhaust connection, insert the reducer flange 9 on the dumper 10. Fix the pipe in position using sufficient pipe clamps (not supplied). Remove any activated charcoal filters. 150 25 10 120 25 9 10 EN 7 7 RECIRCULATION VERSION AIR OUTLET ?Assemble the two halves of the hood body extension piece 14 (if necessary). Push fit the assembled hood body extension piece 14 onto the air outlet (if necessary). Push fit connection 15 onto the hood body extension piece 14 or directly onto the hood body. Insert the connection extension pieces laterally 14. 1 in connection 15. Should the central reinforcing piece of the frame somehow interfere the chimney air outlet grille, it is possible to unscrew it and to place it in another screw hole set. 15 14. 1 14 Flue assembly - Mounting the hood body ?Position the upper chimney section and fix the upper part to the frame using the 2 screws 12c (2, 9 x 6, 5) provided. [. . . ] T1 Turn the suction motor on and off at speed one. Press and hold the button for approximately 2 seconds, After 100 working hours all the with all the loads turned off (Motor and Lights), to reset LEDs (L1-L2-L3-L4) will light up and remain lit to indicate saturation the Filters and turn off the Leds that are lit. After 200 working hours all the LEDs (L1-L2-L3-L4) will light up and start to flash to indicate saturation of the activated charcoal filters. T2 Turn the suction motor on at speed two. [. . . ]