User manual SMEG SR341AS

[. . . ] WE ADVISE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES PROVIDED. INSTALLATION MUST BE CARRIED OUT BY COMPETENT PERSONS IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. [. . . ] Correct disposal enables intelligent recovery of valuable materials. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power supply network, removing it along with the plug. 32 Instructions for the installer 4 POSITIONING OF THE HOB The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). 4. 1 Attachment to support structure Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear border. This appliance is classified as "type Y" in relation to fire hazards and can therefore be mounted against walls higher than the work surface on condition that a certain distance "X" be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. Make sure there is a minimum of 750 mm between the hot plate flames and any shelf that may be installed directly above them. Carefully position the insulating seal supplied on the outer perimeter of the hole made in the counter top as shown in figure 4 (the dimensions in the figure refer from the hole to the inside of the seal), trying to ensure that it sticks across the whole of its surface by applying light pressure with your hands. Fix the hob to the unit using the appropriate brackets B and spacer A as shown in figures 1, 2 and 3. Spacer A will help to keep the hob top at the right distance from the edge of the counter top to avoid future overheating during operation and must be used solely in the front left-hand corner of the appliance. Carefully trim the surplus away from edge C beyond the seal (Fig. 5). 33 Instructions for the installer A+B B B A B B B B Fig. 1 Fig. 2 A B Fig. 3 Fig. 4 34 Fig. 5 20 ÷ 40 Instructions for the installer 5 ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the current electrical system regulations. After installation, the installer must issue a certificate of conformity. 37 Instructions for the installer 7 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, disconnect the appliance from the electrical socket. The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other types of gas the nozzles must be replaced and the primary air adjusted. To replace the nozzles and regulate the burners, you have to remove the top as described in the following paragraph. 7. 1 1. 60 cm hobs with separable control panel. G20 Burner 20 mbar Auxiliary (1) Semirapid r (2) Semirapid l (3) Rapid large (4) Ultrarapid (5) 3. 0 1. 0 1. 0 1. 0 1. 0 G30/G31 28/37 mbar 4. 0 2. 0 2. 0 3. 5 5. 0 90 cm hobs with separable control panel. G20 Burner 20 mbar Auxiliary (1) Semirapid (2) Rapid (3) Fish burner (4) 2. 5 1. 0 1. 5 0. 5 G30/G31 28/37 mbar 3. 0 2. 0 1. 5 8. 0 3. 0 G30/G31 28/37 mbar 4. 0 2. 0 2. 0 3. 5 4. 0 Ultrarapid (5) 1. 5 60 cm hob with built-in control panel. G20 Burner 20 mbar Auxiliary (1) Semirapid r (2) Semirapid l (3) Rapid medio (4) Ultrarapid (5) 3. 0 1. 0 1. 0 1. 5 1. 0 To identify the burners on your hob, refer to the drawings in point "8. 3/8. 4 Arrangement of burners on hob " 41 Instructions for the installer 8 FINAL OPERATIONS Having carried out the above adjustments, reassemble the appliance following, backwards, the instructions in paragraph "7. 1 Removing the separable control panel / 7. 2 Removing the hob". 8. 1 Regulation of minimum for natural gas Reposition the components on the burner and slide the knobs onto the cock stems. Light the burner and set it on the minimum position. Take the knob off again and turn the regulating screw on the side of the cock stem until a steady minimum flame is achieved. Refit the knob and verify the burner flame is stable (turning the knob rapidly from the maximum to the minimum position the flame must not go out). 8. 2 Regulation of minimum for LPG To regulate the minimum for LPG, completely tighten (clockwise) the screw inside or next to the gas tap pin (depending on the model). The diameters of the by-passes for each burner are given in table " 0 Regulation for LPG". [. . . ] · Dry the bottom of the pan before placing it on the electric element. · When cooking with flammable oils and fats, never leave the appliance. · The electric elements will stay hot for a long time after use: do not touch them or place any objects on them. · If any dents appear in the electric element surface, switch it off immediately and contact the nearest authorised servicing centre. [. . . ]