User manual SMEG ST110A.1

[. . . ] Troubleshooting Control Panel Symbols WEEE mark Pag. 22 23 26 28 32 37 39 119 120 F Sommaire 1. Avertissements pour la sécurité et l'utilisation 3. Instructions pour l'installation 4. [. . . ] The machine stops with the tub full of water and the washing remains soaked. To remove the soaked and dripping washing (drip-dry fabrics) turn the ) and press the knob to the drain and spin position (Drain "Start/Pause" button. The water is automatically drained on all programmes without spinning. Press this button to reduce movement of the drum and, consequently, of the washing. Suitable for particularly delicate garments (shirts, silk, curtains, etc. ) Delicates button Half load button 1/2 If the machine is used with a smaller amount of washing than that indicated in the "Programme Chart", press this button to save water, detergent and electricity. This option should not be used for synthetics or woollens. The recommended doses of detergents should be reduced in proportion to the load. 30 F Options enabled LED's These LED's light up when the relative option button is pressed and indicate that the option has been selected. They remain on until the machine switches off or a different selection is made. G Select spin speed or stop Press this button to select one of three spin speed levels, indicated by the spin speed and stop with tub full LED's. The with tub full button* levels are: · · · maximum speed: the machine spins at the indicated speed intermediate speed: the machine spins at the indicated speed final spin disabled and stop with tub full: the machine does not perform all the spins and finishes the washing programme with water in the tub. To drain the water, see the explanations shown in paragraphs 5. 10 and 5. 14 H Spin speed and stop with tub full LED's* The LED's indicate the selected speed level. The LED corresponding to the selected level remains on until the machine is switched off or until a new spin speed is selected. (max. Stains should always be cleaned or diluted immediately as the older they get, the more difficult they are to remove. · Garments may be damaged if fabric care symbols are not observed. Wool ­ Only pure wool, identified by or with the label <<shrink-proof machine washable and dryable>> can be machine washed with the specific programme, other types of wool should be hand-washed or dry-cleaned. 5. 2 OPENING THE DOOR The machine is fitted with a safety device that prevents the door from opening while it is working. Before opening the door, wait 1 or 2 minutes after the programme ends ("End" LED on) to allow the safety device to disengage. Make sure there is no water in the tub and that the drum is not moving. Open the door by pressing the "Open door" button on the front panel and pulling it open. Attention!· If the washing programme is interrupted, you will have to wait from 3 to 15 minutes, depending on the temperature of the water, before the door opens. The water may still be boiling if the washing cycle was performed at high temperatures. If there is still water inside the drum, do not open the door! 32 5. 3 PREPARING THE WASHING Where possible, save electricity by washing full loads divided by type of fabric. Introduce loose washing and alternate large items with small ones. For the first few times, weigh the loads of washing and then rely on your judgement. 5. 4 LOADING THE WASHING 1. [. . . ] tub full To drain the water, proceed as described in the "End of programme" paragraph. Make sure the end of the drain hose is not too low. 6 7 Check that: the machine has been properly levelled as described in paragraph 3. 2 the machine is not too close to walls or furniture the internal moving assembly has been released as described in paragraph 3. 1 the detergent is suitable for automatic machines and is not for hand washing no more than the quantities indicated in the manual are used the unions of the water inlet hose are not loose the end of the drain hose has not moved out of place. 8 Too much foam forms and escapes from the tray Check that: - 9 Water on the floor Check that: - 10 Not all the fabric softener enters the machine or too much water remains in the compartment Make sure that the traps in the detergent tray are correctly positioned and are not clogged. Clean them as indicated in paragraph 6. 4. 39 11 The machine does not spin The unbalanced load sensor has triggered because the washing is not uniformly distributed inside the drum. If the washing is wet at the end of the cycle, distribute it well inside the basket and repeat just the spin cycle. [. . . ]