User manual SMEG STU1846 MANUALE D'INSTALLAZIONE

[. . . ] DISHWASHER INSTALLATION INSTRUCTIONS CONTENTS CONTENTS Contents 1 2 3 3. 1 3. 2 4 5 5. 1 5. 1. 1 5. 1. 2 5. 2 5. 2. 1 5. 2. 1. 1 5. 2. 1. 2 5. 2. 2 5. 3 5. 3. 1 5. 3. 2 5. 3. 3 5. 4 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTALLATION MATERIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Kit supplied with dishwasher (models sta_4645/sta_8743) . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 5-01) of the foot and then fit the supplied washer; do this on both feet. Screw the feet onto the appliance until the washers touch the base; the two feet must be manually adjusted to the same height to prevent excessive differences in height between one foot and the other. TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO TURN THE DISHWASHER UPSIDE-DOWN. A B Fig. 5-01 Rev 0. 0 13 12 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 5. 1. 2 Levelling the appliance Level the appliance using the relative adjustable feet (e. g. : ref. 5-02); use an open-ended wrench to rotate the feet until the dishwasher is perfectly level. Some models are fitted with just one rear foot which can be adjusted with a screw located at the bottom front of the appliance (ref. THE DISHWASHER MUST ALWAYS BE CONNECTED TO THE WATER SYSTEM WITH NEW HOSES; OLD OR USED HOSES MUST NEVER BE REUSED. 16 Rev 0. 0 15 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 5. 2. 1. 1 Connecting to the water tap Connect the inlet hose to a threaded ¾” gas cold water tap, fitting the supplied filter (ref. Firmly secure the hose by tightening the relative ring nut with your hands (ref. 5-06); finish by tightening another ¼ turn using a pair of plumbing pliers. 5-06) the filter is already present in the threaded ring nut. The dishwasher can be filled with water at a temperature of less than 60°C (140°F). If the appliance is filled with hot water, washing times will be reduced by about 20 minutes, but efficiency will be slightly impaired. Make the connection to the domestic hot water tap using the same methods described for connecting the appliance to the cold water tap. • Recommended temperature: 49°C (120°F), max. • Recommended water pressure: 0. 5 - 9 bar (7 -130 PSI). If the pressure is too high, fit a pressure reducer. A rubber hose connected to a sink spray may burst if installed on the same pipes feeding the dishwasher. If your sink is fitted with this accessory, remove the hose and plug the hole. EN Fig. 5-06 Rev 0. 0 17 16 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Do not cut the inlet hose (see fig. If the hose is cut, the dishwasher will not work, water will leak and you may be injured. If the hose is too long, wind it up tidily and place it behind the appliance. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses. EN Fig. [. . . ] Use the screwdriver to secure the door handle before hooking the panel to the dishwasher (see fig. N. B. : the screws are not supplied. EN Fig. 5-21 Attach the door panel: fit the hooks into their slots on the dishwasher and allow the panel to slide downwards and slip in to place (see fig. 5-22 28 Rev 0. 0 27 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Secure the door to the panel with the supplied screws. [. . . ]