User manual SMEG SWM62F

[. . . ] FULL ELECTRONIC WASHING MACHINE USER MANUAL THE CONTENTS SECTION 1:BEFORE USING Safety warnings Recommendations SECTION 2:INSTALLATION Removal of transportation screws Adjustment of feet Electrical connection Water supply connection Water drain connection SECTION 3:TECHNICAL SPECIFICATIONS SECTION 4:CONTROL PANEL Start/Pause button Function indicator lights Function buttons Program knob SECTION 5:WASHING YOUR LAUNDRY Before washing Running the machine SECTION 6:MAINTENANCE AND CLEANING Water inlet filters Pump filter Detergent drawer Siphon plug The cabinet The drum Remove of your machine from lime SECTION 7: PRACTICAL INFORMATION SECTION 8:AVOIDING MINOR FAULTS SECTION 9:AUTOMATIC FAILURE DETECTION SYSTEM SECTION 10:INTERNATIONAL WASHING SIGNS 1 SECTION 1:BEFORE USING SAFETY WARNINGS Do not use a multiple socket or extension cord. Do not insert a plug with damaged or broken cord into the socket. If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard. Never remove the plug from the socket by pulling from the cord section. [. . . ] Before opening the filter cover, place a cup in front of the filter cover to prevent flow of the remaining water in the machine. Loosen the filter cover by rotating it counter clockwise and drain the water. Remove the foreign materials from the filter. Check for the rotation of the pump manually. After you have cleaned the pump, fit the filter cover by rotating clockwise. Do not forget that if you do not fit in the filter cover properly, it will leak water. 13 WARNING! Danger of being scalded!Since the water inside the pump maybe hot, wait for it to cool. DETERGENT DRAWER Detergents may form a sediment in your detergent drawer or in housing of the detergent drawer in time. To clean the sediment, pull out the detergent drawer from time to time. To pull out the detergentdrawer: Pull the detergent drawer to the end. (DIAGRAM-1) Lift the front of the drawer, continue to pull until the drawer is pull out. (DIAGRAM-2) Wash will an old toothbrush and excessiveamount of water. Take off the leftover detergent avoid to drop into your machine. After drying the detergentdrawer put into the housing in the same manner you pull out. DIAGRAM-1 DIAGRAM-2 14 SIPHON PLUG Pull out the detrgent drawer. Remove the siphon plug and clean the residues of the softener thoroughly. Fit the cleaned siphon plug in its location. Check if it placed properly. THE CABINET Clean the exterior surface of the cabinet of your machine with lukewarm water and a cleaning substance that will not irritate the cabinet. After rinsing with clean water, wipe it with a soft and dry cloth. WARNING! If the machine is installed in a location where the ambient temperature can fall below 0 C, do the following when it will not be in use: Plug in the machine. Close the water tap and pull out the water inlet hose or hoses from the tap. Place the ends of the water drain and water inlet hoses in a cup on the ground. Adjust the program knob to "Draining" program. Run the program by pressing the start/pause button. Unplug your machine when the program is over (program end light is on). When you complete these proces, the remaining water inside the machine will be drained and thus formation of ice in the machine will be prevented. When you operate your machine again, be sure that the ambient temperature is above 0 C. THE DRUM Do not leave metal parts like needles, staples or coins inside your machine. [. . . ] In the next washing operation, use the maximum detergent amount declared by the detergent producer. There are residues of detergent on the clothes. There are gray stains on the clothes. These stains may be caused by oil, cream or ointment . (**) See the section concerning instalations your machine. 20 FAILURE PROBABLE CAUSE The spining process is not done or starts with delay . No failure. The unbalanced load control may works in that way. METHODS OF ELIMINATION The unbalanced load control system will try to distribute your clothes in a homogenous manner. After your clothes are distributed, passage to spining process will be realized. In the next washing process, place your clothes into the machine in a wellbalanced manner. SECTION 9: AUTOMATIC FAILURE DETECTION SYSTEM Your machine is equipped with systems which will both take the necessary precautions and warn you in case of any failure by controlling it self constantly during the washing processes. FAILURE CODE FAILURE INDICATOR PROBABLE FAILURE Err 01 The start/pause light blinks. The door is not shut properly. THE PROCESS TO BE DONE Shut the door properly so that you hear the click. If the problem persists, turn off the machine unplug and apply to the nearest authorized service immediately. 21 FAILURE CODE FAILURE INDICATOR PROBABLE FAILURE Err 02 The program ready light blinks. The water level in your machine is below heater. [. . . ]