User manual SMEG TLS6-1

[. . . ] Programme sequence indicator (over the line) PROGRAMME CHART C This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately: H. "Water tap closed" indication J. "Clean pump" indication 1) 2) I J G H F D. G. Start delay indicator (under the line) "Variable spin" button "Start/Pause" button "Reset" button "Door open" indication Max. [. . . ] The edge of the sink must be no more than 100 cm from the floor. If you need to add an extension, use a flexible hose of the same size and secure the unions with screw-on hose clips. Maximum overall drain hose length: 2. 50 m. Maximum drain height ("U" bend): 100 cm. Important: Make sure there are no kinks in the drain hose and take precautions against it falling while the washing machine is running. A B C GB 4 ELECTRICAL CONNECTION Do not use extension leads or multi sockets. Electrical connections must be made in accordance with local regulations. 1) Warning - this washing machine must be earthed This washing machine is normally supplied with a mains lead having a plug fitted in the factory which has been checked for correct earth continuity. If the fitted plug is not suitable for your socket outlet, or if the machine's mains lead is not fitted with a plug, you should fit a suitable new, good quality plug by following the instructions in (2) below. Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it be inserted into a socket. 2) CONNECTION TO A REWIRABLE PLUG - to be carried out only by a qualified electrician The wires in the mains lead are coloured in accordance with the following code: BLUE - "NEUTRAL" ("N") BROWN - "LIVE" ("L") GREEN AND YELLOW - "EARTH" ("E") To fit a new plug, proceed as follows: 2. 1) Polarized Plugs (e. g. 3 pin, 13 amp plug conforming to BS 1363A) a. The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the letter "E" or by the Earth symbol or coloured green and yellow. The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured blue. The BROWN wire must be connected to the terminal which is marked with the letter "L" or coloured brown. 2. 2) Non-polarized plugs (e. g. 2 pin with side earth contact) The wire which is coloured GREEN AND YELLOW must be connected to the earth contact. The other two wires should be connected to the two pins, irrespective of colour. FUSE REPLACEMENT If the mains lead of this washing machine is fitted with a BS 1363A 13 amp fused plug, replace the fuse only with an A. S. T. A. approved type conforming to BS 1362 and proceed as follows: Remove the fuse cover (A) and the fuse (B). Fit the replacement 13 A fuse into the fuse cover. For all other types of plug, the supply socket should be protected by a 16 A fuse or circuit breaker at the distribution board. GB 5 BEFORE THE FIRST WASH CYCLE To remove any residual water used in testing by the manufacturer, we recommend that you carry out a short wash cycle without laundry. Add a small amount of detergent (maximum 1/3 of the quantity the detergent manufacturer recommends for lightly soiled laundry) to the main wash chamber of the detergent dispenser. Select and start programme "Synthetics" at 60°C (see separate the programme chart). PREPARATION OF THE LAUNDRY Sort the laundry 1. · Type of fabric / care label symbol Cottons, mixed fibres, easy care/synthetics, wool, handwash items. [. . . ] "Water level too high" (after programme cancellation or false operating). Switch off appliance and then switch it on again, select programme "Drain" and start within 15 sec. "Waterstop fault" Switch off appliance, pull out mains plug and turn water tap off. Tilt appliance forward carefully to allow collected water to flow out from the bottom. [. . . ]