User manual SMEG UKST120.2

[. . . ] 1. 10- If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then this must be of the room sealed or balanced flue type. If other types of flue or appliance are fitted, ensure that there is an adequate supply of air into the room. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0, 04 mbar to prevent fumes being drawn back into the room by the cooker hood. 1. 11- The appliance must be positioned so that the plug is accessible. [. . . ] To remove the metal grille, pull forward on the right hand side so that the hinge pin on the back of the grille will be released from the slot in the side of the casing. 2. 2 - Wall cabinet fixing a - Predrilled wall cabinet: fix the hood onto the wall cabinet base panel using the four screws 4. 2 x 45 mm (supplied with the fixing kit). It is not necessary to open the metal grille. b - No predrilled wall cabinet: b. 1 If the hood is provided with a paper fixing template, follow the instructions. b. 2 If the hood is not provided with a paper fixing template, position the hood on the wall cabinet base panel and pilot drill the 3. 5 x 16 mm screws (not supplied with the fixing kit) from the inside onto the wood. 2. 3 - Wall mounting a - Drill two Ø 8 mm holes on the wall using the paper template, insert two rawl plugs and two 4. 2 x 44, 4 mm screws leaving 5 mm untightened. Open the metal grille panel, hook the hood on and fully tighten the screws. b - If the hood is not provided with a paper fixing template, drill two Ø 8 mm holes (see draw. ), insert the plugs and screws, proceeding as directed under paragraph a. c - For wall mounting using wallbrackets (optional), follow the instructions of the fixing template. d - Pay attention to the safety regulation of point 1. 6. 2. 4 - Choice of operating mode a - Evacuation mode To check that the hood is set up for evacuation, open the grille panel and make sure that the conversion lever or the change-over knob on the centrifugal unit is in the DUCTING position. For ducting to the outside, the hood is supplied with a rear and top outlet. A flange spigot of 100 mm diameter (120 mm in certain models) is usually fitted on the top outlet and a blanking plug on the rear outlet. If you choose to duct the hood from the rear of the casing, you should invert the position of the flange and of the blanking plug. We strongly recommend therefore to clean and replace filters in accordance with the manufacturer instructions. 4. 2 - Cleaning Metal self- supporting Grease Filters · · · · The filters are washable and must be cleaned at least every 2 months of operation, or more frequently for particularly heavy usage. Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. Wash the filters, taking care not to bend them. When refitting the filters, make sure that the handle is visible on the outside. 4. 3 - Charcoal filter The charcoal filter is a chemical filter to be used only when the hood is in the recycling position. To replace the charcoal filter, open the grille and remove the thumb screw through the centre of the charcoal filter. If the filter is of the interlocking type, turn the filter anticlockwise. For a good performance replace the charcoal filter on average every three months. 4. 4 - Worktop illumination If a lamp fails to function at any time, open the metal grille panel and check that the lamp is fully screwed into the holder. When changing the lamp, an identical replacement must be fitted to ensure a safe working of the hood. 4. 5 - Cleaning The metal work should be cleaned regularly, at least once a month, using mild household cleaner and polish. For all operations from point 4. 1 to point 4. 4 and in particular for point 4. 3, pay special attention to the safety regulation 1. 9. EN 1 12 Il simbolo sul prodotto o sulla confezione indica che il prodotto non deve essere considerato come un normale rifiuto domestico, ma deve essere portato nel punto di raccolta appropriato per il riciclaggio di apparecchiature elettriche ed elettroniche. Provvedendo a smaltire questo prodotto in modo appropriato, si contribuisce a evitare potenziali conseguenze negative per l'ambiente e per la salute, che potrebbero derivare da uno smaltimento inadeguato del prodotto. Per informazioni più dettagliate sul riciclaggio di questo prodotto, contattare l'ufficio comunale, il servizio locale di smaltimento rifiuti o il negozio in cui è stato acquistato il prodotto. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. [. . . ] Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Le symbole sur le produit ou son emballage indique que ce produit ne peut être traité comme déchet ménager. Il doit plutôt être remis au point de ramassage concerné, se chargeant du recyclage du matériel électrique et électronique. [. . . ]