User manual SMEG UKSTX4

[. . . ] 16 5. 2 Note on display of temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5. 3 Parameter programming procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5. 4 Modifiable parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5. 5 Alarm trigger time thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In this case warranty cover will be forfeited. IMPORTANT: Whenever the type of detergent or rinse aid is changed, it is ABSOLUTELY ESSENTIAL to flush out the peristaltic pumps by placing the external intake pipes in water for a few cycles. Always use only products specifically recommended for use in a dishwasher. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance's water system. The internal pipes of the detergent and rinse aid pumps should be replaced by the AfterSales Service every 12 months or 15, 000 wash cycles and operation of the diaphragm rinse aid pump should be checked. 15 CW 510/D/SD CW 510M/MD/MSD 5 SET-UP Setup During first startup, the functions/parameters listed below must be set or adjusted: A series of operations can be carried out when the dishwasher is first installed to customise it to the user's requirements. To modify the parameters, proceed as follows. 5. 1 Display Contents The two green digits provide the following information: Appliance off but powered up: all decimal points on both digits Appliance on: Boiler temperature Washing phase: Tank temperature Pause phase: Boiler temperature Rinse phase: Boiler temperature Programming phase: See parameter programming section Error message: See error messages section 5. 2 Note on display of temperatures Both the Boiler and the Tank temperatures provide instantaneous readings of the current value picked up by the probe, but due to the thermal inertia of the probe or its seat, wait about 1' after the heating element power absorption reading to obtain the real temperature. 5. 3 Parameter programming procedure To access the programming menu, proceed as follows: 1) switch the appliance off with the (On Off) key 2) Within 6 seconds, press key P1 (SHORT wash) 7 times. Wait for the 6 seconds to pass; at the end P0 appears on the display 3) Use key P1 to select the parameter to be modified 4) Press the PUMPOUT KEY to display the parameter for modification 5) Modify the parameter by pressing key P1 6) Confirm the change by pressing the PUMPOUT key 7) Select the other parameters for modification in the same way and proceed as described above 8) After setting all the appliance parameters, press the On Off key to quit. 16 5. 4 Modifiable parameters CW 510/D/SD CW 510M/MD/MSD This table lists the model choice or cycle and temperature option parameters. E. 7 Boiler heating malfunction (does not heat up) E. 8 Tank heating malfunction (does not heat up) E. 9 Microprocessor failure circuit board relay failure boiler heating element faulty or "furred" with limescale boiler temperature probe faulty or incorrectly positioned circuit board relay failure tank heating element faulty or "furred" with limescale tank temperature probe faulty or incorrectly positioned Replace circuit board 7 INSTRUCTIONS FOR THE USER 7. 1 Control panel Onoff button Total emptying button (tank and boiler) Regeneration key (only if softener is fitted) L1 power on LED L2 pumpout in progress LED L3 no salt LED (only if softener is installed) L4 no salt LED (only if softener is installed) 21 CW 510/D/SD CW 510M/MD/MSD Short cycle key Medium cycle key Long cycle key L5 short cycle program LED L6 medium cycle program LED L7 long cycle program LED 7. 2 Before washing Use only detergents and rinse aids for industrial dishwashers. Do not use detergents intended for hand washing. We recommend the use of Smeg products, specially developed for this dishwasher. When topping up the tanks, take care not to swap the products; this might damage the dishwasher and cause malfunctions. Do not mix different detergents; this would damage the dispenser device. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance's water system. Industrial dishwasher detergents may cause serious irritation. Comply carefully with the instructions provided by the detergent producer on the pack. Turn on the mains water tap (user) CHECK 2. The level of detergent and rinse aid in the containers. That there is regenerating salt in the relative container (if fitted). [. . . ] Check that water intake filter is not fouled. If you are unable to solve the problem, call the aftersales service. Check container of rinse aid and whether it is suitable for the type of mains water. If the problem persists, contact the aftersales service. [. . . ]