User manual SMEG W341A

[. . . ] Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 2 EN 1. THE NEW WASHING SYSTEM This new washing machine is the outcome of years of research. [. . . ] There must be a space of at least 2mm all around. The rear part of the machine must also remain some distance away from the back wall. If the recessing cavity is higher than 820mm the opening between the floor and sides of the machine (when this is installed at the end of a line of furniture), must be completely closed in compliance with the relative safety provisions. The covering must make it impossible for users to touch live parts of the electrical system and must require tools in order to be removed. Our company declines all responsibility for damages caused by failuresto comply with these safety provisions. 12 EN 3. 7. 6 Fitting the plinth The base plinth for kitchen furniture must be removable in the area in front of the washer dryer to allow access for routine maintenance of the drain pump if it becomes clogged with buttons, fasteners, or similar objects, and for our engineers to be able to remove the washer dryer for service. Please note: our engineers will not remove plinths that have been fixed into position by glues or mastics, or where removal could cause third-party damage. If a plinth is fitted directly onto the washer dryer then it must be done so with four screws inserted into the four pre-set holes Application of the plinth to the furniture must not involve elimination or modification of the washing machine plinth. Owing to safety reasons, this may not be removed. It must absolutely remain intact and fixed to the washing machine. 13 EN 4. DESCRIPTION OF CONTROLS 4. 1 CONTROL PANEL All the commands and controls of the appliance are assembled together on the front panel. Models without delayed start option Models with delayed start option Description of controls A B C D E F G H I L M N Q R Open door button ON-OFF and programme selection knob Time remaining shown on display LED Spin speed shown on display LED Heating phase LED Display Select spin speed button Options buttons Options enabled LED's Start-Pause button Start-Pause button LED Delayed start time shown on display LED Select delayed start button Select delayed start button LED 14 EN A Open door button Press the button to open the door. Chapter 5 ­ Washing instructions ­ explains how the door works and how to use it. B ON-OFF and washing programme selection knob This knob lets you: · switch the machine on and off by moving it in either direction from the OFF position (knob indicator vertical) · select washing temperatures within the various fabric sectors by turning it in both directions The knob does not move while the programme is running. N. B. : Press the economy cycle button to obtain a maximum washing temperature of 60° C and the elimination of the pre wash cycle. Economy cycle button - e Extra Rinse button In areas with soft water or to improve rinsing, press this button (optional for intensive programmes) to enable the extra rinse function (about 20% more water). Delicates button Press this button to reduce movement of the drum and, consequently, of the washing. Suitable for particularly delicate garments (shirts, silk, curtains, etc. ) Half load button 1/2 If the machine is used with a smaller amount of washing than that indicated in the "Programme Chart", press this button to save water, detergent and electricity. This option should not be used for synthetics or woollens. The recommended doses of detergents should be reduced in proportion to the load. I Options enabled LED's These LED's light up when the relative option button is pressed and indicate that the option has been selected. They remain on until the machine switches off or a different selection is made. 16 EN L "Start/Pause" button Press this button to start the selected washing programme. During washing, press the "Start/Pause" button for about 3 seconds to pause the washing cycle. During the pause, the "Time remaining" Led flashes and STOP appears on the display. To resume the washing cycle from where it left off, simply press the "Start/Pause" button again. This LED lights up when the washing cycle starts (StartPause button pressed) and remains on until the end of the programme. Press this button repeatedly to select after how many hours you want the selected washing/drying programme to start. The default value is 0 hours 0 minutes and each time the button is pressed it increases by 60' up to 12h and by 120' for the following 12 hours, up to 24 hours. M Start-Pause button LED N Select delayed start button* O Select delayed start button LED* The LED lights up while the delayed start time is being selected and remains on until the programme starts. P Delayed start time shown on This LED indicates that the display is showing the selected delayed start time. [. . . ] · Clean the filter with water and a brush. · When screwing the inlet hose back on to the tap, make sure the filter is correctly positioned. 25 EN 7. TROUBLESHOOTING This product complies with current safety regulations governing electrical equipment. For safety reasons, all technical inspections or repairs must be performed by qualified technicians in order to prevent hazardous situations for users. [. . . ]