User manual SMEG W500CNX

[. . . ] · Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. · Do not flambè under the range hood; risk of fire · This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. · Children should be supervised to ensure that they do not play with the appliance. 650 mm min. MAINTENANCE · Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. · Clean and/or replace the Filters after the specified time period (Fire hazard). [. . . ] · Clean and/or replace the Filters after the specified time period (Fire hazard). · Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 1 11 1 CHARACTERISTICS Dimensions min. 850 740 ø120 80 51 598 / 898 Min. 500mm 650mm 300 150 572 265 254 490 Components Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 2 1 Telescopic Chimney comprising: 2. 1 1 Upper Section 2. 2 1 Lower Section 9 1 Reducer Flange ø 150-120 mm 14 1 Hood Body Air Outlet Extension Piece consisting of two Half Shells 14. 1 2 Air Outlet Connection Extension 15 1 Air Outlet Connection Ref. Q. ty Installation Components 7. 2. 1 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 12a 6 Screws 4, 2 x 44, 4 12c 6 Screws 2, 9 x 9, 5 Q. ty Documentation 1 Instruction Manual Ref. 1 107. 5 70 253 433 90 ø150 max. 1050 132 15 14. 1 12a 14 9 7. 2. 1 11 2. 1 2 2. 2 12c 11 12a 1 EN 1 12 2 INSTALLATION Wall drilling and bracket fixing 1÷2 11 12a 116 116 Wall marking: · Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. Insert the connection extension pieces laterally 14. 1 in connection 15. Make sure that the outlet of the extension pieces 14. 1 is horizontally and vertically aligned with the chimney outlets. If this is not the case, adjust the position by either reversing the connection extension pieces 14. 1 or by cutting the hood body extension 14 along one of the thinner section channels denoting the prefixed lengths, then reassemble as described previously. Ensure that the activated charcoal filters have been inserted. 15 14. 1 14 EN 1 14 4 ELECTRICAL CONNECTION · Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. · Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. Chimney assembly Upper exhaust Chimney · Slightly widen the two sides of the upper chimney and hook them behind the brackets 7. 2. 1, making sure that they are well seated. · Secure the sides to the brackets using the 4 screws 12c (2, 9 x 9, 5) supplied. Lower exhaust Chimney · Slightly widen the two sides of the chimney and hook them between the upper chimney and the wall, making sure that they are well seated. · Fix the lower part laterally to the hood body using the 2 screws 12c (2, 9 x 9, 5) supplied. 2. 1 2 2. 2 7. 2. 1 12c 12c EN 1 15 5 USE L S V1 V2 V3 L S V1 V2 V3 Light Led Motor Speed Intensive Switches the lighting system on and off. Switches the extractor motor on and off at low speed. Used to provide a contin-uos and silent air change in the presence of light cooking vapours. [. . . ] Switches the extractor motor on and off at low speed. Used to provide a contin-uos and silent air change in the presence of light cooking vapours. Medium speed, suitable for most operating conditions given the optimum treated air flox/noise level ratio. Maximum speed, used for eliminating the highest cooking vapour emission, including long periods. EN 1 16 6 MAINTENANCE Grease filters CLEANING METAL SELF- SUPPORTING GREASE FILTERS · The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. [. . . ]