User manual SMEG W75SX

[. . . ] 15 5. 2 Note on display of temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5. 3 Parameter programming procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5. 4 Modifiable parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5. 5 Alarm trigger time thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance's water system. The internal pipes of the detergent and rinse aid pumps should be replaced by the AfterSales Service every 12 months or 15, 000 wash cycles and operation of the diaphragm rinse aid pump should be checked. 14 NW511 5 SET-UP Setup During first startup, the functions/parameters listed below must be set or adjusted: A series of operations can be carried out when the warewasher is first installed to customise it to the user's requirements. To modify the parameters, proceed as follows. 5. 1 Display Contents The two green digits provide the following information: Appliance off but powered up: all decimal points on both digits Appliance on: Boiler temperature Washing phase: Tank temperature Pause phase: Boiler temperature Rinse phase: Boiler temperature Programming phase: See parameter programming section Error message: See error messages section 5. 2 Note on display of temperatures Both the Boiler and the Tank temperatures provide instantaneous readings of the current value picked up by the probe, but due to the thermal inertia of the probe or its seat, wait about 1 minute after the heating element power absorption reading to obtain the real temperature. 5. 3 Parameter programming procedure To access the programming menu, proceed as follows: 1) switch the appliance off with the (On Off) key 2) Within 6 seconds, press key P1 (SHORT wash) 7 times. Wait for the 6 seconds to pass; at the end P0 appears on the display 3) Use key P1 to select the parameter to be modified 4) Press the PUMPOUT KEY to display the parameter for modification 5) Modify the parameter by pressing key P1 6) Confirm the change by pressing the PUMPOUT key 7) Select the other parameters for modification in the same way and proceed as described above 8) After setting all the appliance parameters, press the On Off key to quit. 15 5. 4 Modifiable parameters NW511 This table lists the model choice or cycle and temperature option parameters. F/M M F M ID P0 P1 P2 Description Appliance Type Appliance Model Boiler temperature Default 05 05 80C Notes Construction version Do not modify Do not modify Step 1 degree WARNING: The actual boiler temperature depends on whether the connection is singlephase or threephase. With threephase connection, do not set more than 85° Step 1 degree 0=off 1=on 0=off 1=on Real=measured+Offset Real=measured+Offset 0= filtered, 1= real Do not modify M M M M M M F P3 P4 P5 P6 P7 P8 P9 Tank temperature Thermostop option Soft Start option Boiler temperature offset Tank temperature offset Real temperature display Tank probe type 58C 01 01 00 04 01 01 Note for P6 and P7: negative numbers are indicated by illumination of both decimal points (e. g. : 12 "1. 2. ") 5. 5 Alarm trigger time thresholds This table lists all the safety device trigger time thresholds. F/ M F F F F F ID A0 A1 A2 A3 A4 Description Boiler max. When topping up the detergent and rinse aid containers, take care not to swap the products; this might damage the warewasher and cause malfunctions. Do not mix different detergents; this would damage the dispenser device. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance's water system. Industrial warewasher detergents may cause serious irritation. Comply carefully with the instructions provided by the detergent producer on the pack. Turn on the mains water tap (user) CHECK 2. The level of detergent and rinse aid in the containers. That there is regenerating salt in the relative container (if fitted). That the filters are in place, the spray arms rotate, and there are no foreign bodies in the warewasher. Switch on the master switch (user): the word "OFF" appears on the display. 22 NW511 7. 3 First use each day (tank and boiler empty) Display shows Actions and what happens Door closed and master switch on ON: Press and hold it down for 23 seconds; the ON/OFF light and the two digits on the display light up. [. . . ] If you are unable to solve the problem, call the aftersales service. Check temperature shown on the display, call the aftersales service if less than 50°C Increase wash cycle duration, especially if dirt has dried on. Check that water intake filter is not fouled. If you are unable to solve the problem, call the aftersales service. [. . . ]