User manual SMEG WD4060D

[. . . ] This user-friendly manual will provide answers to all your questions about use of the dishwasher. For any other information about use and maintenance of the dishwasher, read the enclosed manual carefully. USER INSTRUCTIONS: useful information is provided for the use of the washing programs and all the dishwasher's functions. User instructions 1. Description of the controls 1. 1 Front panel All the dishwasher control are grouped on the front panel. 1 2 3 4 5 6 7 8 9 10 11 12 13 ON/OFF BUTTON SELECTION PROGRAMS BUTTONS (P1. . . P5) DELAY PROGRAM BUTTON (on some models only) ½ LOAD WASH BUTTON (on some models only) "3/1" OPTION BUTTON (on some models only) START/PAUSE BUTTON POWER ON LIGHT PROGRAMS LIGHTS DELAY PROGRAM LIGHTS (on some models only) ½ LOAD WASH LIGHT (on some models only) PHASES/PROGRAM LIGHTS NO SALT LIGHT (on some models only) NO RINSE AID LIGHT (on some models only) RECESSED DOOR HANDLE User instructions For AAA 12 place-settings models only (see energy label) PROGRAM SELECTION TYPE AND GRADE DIRT PROGRESS PROGRAM DURATION MINUTES (2) CONSUMPTION WATER LITRES (1) POWER KWh (2) SOAK PANS AND DISHES IN WAITING OF COMPLETING THE LOAD Cold prewash 15 6 0, 03 QUICK DISHES NOT MUCH DIRTY AND WITH "FRESH DIRT" WITHOUT RESIDUAL DRY Wash at 38°C Cold rinse Rinse at 58°C Wash at 55°C Cold rinse Rinse at 68°C Dry Cold prewash Wash at 40°C Wash at 55°C Cold rinse Rinse at 68°C Dry Wash at 70°C Cold rinse Rinse at 68°C Dry Cold prewash Wash at 45°C Cold rinse Rinse at 68°C Dry Cold prewash Wash at 55°C Cold rinse Rinse at 68°C Dry Cold prewash Wash at 50°C Wash at 65°C Cold rinse Rinse at 68°C Dry Prewash at 45°C Wash at 70°C Cold rinse Rinse at 68°C Dry 45 13 0, 80 ECO PANS AND DISHES NOT VERY DIRTY BUT WITH DRY RESIDUALS 100 14 1, 20 AUTO 40-50 WASH IMMEDIATELY AFTER USE FOR DISHES WITH NORMAL DIRT (**) (**) (**) STRONG PANS AND DISHES VERY DIRTY 95 17 1, 45 DELICATE + DISHES NOT VERY DIRTY 75 17 1, 05 BIO (*) + PANS AND DISHES DIRTY AND WITH DRY RESIDUALS 180 15 1, 05 AUTO 60-70 + PANS AND DISHES DIRTY AND WITH DRY RESIDUALS (**) (**) (**) SUPER + PANS AND DISHES VERY DIRTY AND WITH DRY RESIDUALS 110 20 1, 60 Only run the soak program with half loads. The HALF LOAD - "3/1" option (4) is available for all programs except the soak program. [. . . ] IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE. DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER. IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE, DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM THE WATER SUPPLY. IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW. IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE. THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN: REPAIRS CARRIED OUT BY UNAUTHORISED PERSONS WILL INVALIDATE THE WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER. The manufacturer declines all responsibility for damage to persons or property resulting from failure to observe the above precautions, from tampering with even a single component of the appliance, or from the use of non original spare parts. Installation instructions 2. Installation and hook-up Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. Safety and operating instructions". User instructions 3. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: · · · Adjust the water softening system; Add the regenerating salt; Add the rinse aid and detergent. 3. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF ­ 24-31°dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1. 7 Kg of salt in grains. Some models are equipped with an optical no-salt indicator. In these models, the cap of the salt container contains a green float which descends as the salt concentration in the water drops. When the green float can no longer be seen through the transparent cap, the container must be topped up with regenerating salt. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening. [. . . ] At this point it is possible to load larger sized plates into the lower basket. To return to the original position, pull out the upper basket again and press the release lever. User instructions 4. Cleaning and maintenance Before carrying out any work, always disconnect the appliance from the electrical power supply. 4. 1 General warnings and recommendations Avoid the use of acidic or abrasive detergents. Clean the outer surfaces and door-lining of the dishwasher regularly using a soft cloth moistened with water or with a normal detergent suitable for painted surfaces. [. . . ]