User manual SMEG WD7000B

[. . . ] BEFORE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION OF FRONT PANEL CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CLOCK AND PROGRAMMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7. 1 Setting the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] GET TO KNOW YOUR OVEN CONTROL PANEL OVEN LIGHT OVEN FAN SHELF AND TRAY RUNNERS ROOF LINER PIZZA PLATE 5. BEFORE INSTALLATION Never leave packaging residues unattended in the home. Separate waste packaging materials by type and consign them to the nearest separate disposal centre. The inside of the appliance should be cleaned to remove all manufacturing residues. When the oven and grill are used for the first time, they should be heated to the maximum temperature for long enough to burn off any oily residues left by the manufacturing process, which might contaminate foods with unpleasant smells. After an interruption in the electricity supply, the programmer display flashes at regular intervals. For setting instructions, see point "7. Clock and programmer". 30 Instructions for the User 6. DESCRIPTION OF FRONT PANEL CONTROLS All the oven's control and monitoring devices are placed together on the front panel. The table below provides the key to the symbols used. THERMOSTAT KNOB The cooking temperature is selected by turning the knob clockwise to the required setting, between 50° and 280°C. FUNCTION SELECTOR KNOB Turn the knob either way to select one of the following functions: NO FUNCTION SET GRILL ELEMENT + FAN GRILL ELEMENT IN OPERATION ALTERNATING WITH BOTTOM HEATING ELEMENT + FAN TOP + BOTTOM HEATING ELEMENTS BOTTOM HEATING ELEMENT + FAN FAN HEATING ELEMENT GRILL ELEMENT TOP + BOTTOM HEATING ELEMENTS + FAN HEATING ELEMENT AUTOMATIC CLEANING CYCLE (PYROLYSIS) GRILL ELEMENT + ROTISSERIE TOP + BOTTOM HEATING ELEMENTS+FAN 31 Instructions for the User THERMOSTAT LIGHT Flashes to indicate that the oven is heating up. When the light stops flashing and remains constantly on, the preset temperature has been reached and will be maintained until the oven is switched off. Very fatty meats can be placed inside the oven when it is still cold. Place frozen meat in the oven directly, without thawing. The only precaution required is to set temperatures about 20 °C lower and cooking times about 1/4 longer than for fresh meat. Use deep containers to prevent splashes from dirtying the sides of the oven. 10. 2 Hot air cooking FUNCTION SELECTOR THERMOSTAT 50 ÷ 280 °C This system is suitable for cooking on several shelves, even with foods of different kinds (fish, meat, etc. ) without cross-contamination of flavours or smells. The air circulation inside the oven ensures uniform heat distribution. Multiple cooking is possible provided that all foods require the same temperature. 36 Instructions for the User 10. 3 Grilling FUNCTION SELECTOR THERMOSTAT Used for quick browning of foods. The tray should be placed on the top runner. For short processes and small amounts, place the shelf on the third runner from the bottom. For longer cooking times and grilling on large surfaces, place the shelf on lower runners, depending on the size of the food. Keep the door closed when grilling is in progress. Grilling with the door open may permanently damage the oven and reduce operating safety. 10. 4 Hot air grilling FUNCTION SELECTOR THERMOSTAT Allows uniform heat distribution with better penetration to the core of foods. [. . . ] To reassemble, fit the hinges into their grooves, then lower the door into place and extract the pins. 45 Instructions for the User 12. 3 Removing the inside glass with the door cold The glass in the door should always be kept thoroughly clean. For easier cleaning, the door glazing can be fully removed by proceeding as described below. After opening the door and locking it in place as described in point "12. 2 Removing the door", remove the three panes of glass. All extracted in two stages: first extract it from the guide "A" (see detail) by sliding it towards you and lifting it slightly, then also free it from the guide "B". [. . . ]