User manual SMITH CORONA WS100MAN

[. . . ] 7 Selecting Line Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Setting Impression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Setting Margins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Shift and Shift Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 5) Presss the CODE + = (SETTING) key. Changing The Print Wheel 1) Move the print carrier to the center of the platen using the SPACE or BS key. 2) You will see a lever on the right side of the carrier. Pull this lever toward you and lift out the daisy wheel. 3) Place the daisy wheel into the slot with the characters facing the platen. 5) Press the CODE + = (SETTING) key. -56 Changing The Correction Tape 1) Move the print carrier to the center of the platen using the SPACE or BS key. 2) To replace the correction tape, lift out the typing ribbon cassette (see Changing The Ribbon Cassette) and remove the two spools of the lift off tape by pulling them outwards. 3) Place the empty spool of new tape on the left pin so that the tape winds clockwise. Pull the tape around the right guide and place the loaded spool on the right pin so that the tape unwinds counter-clockwise. 5 Make sure the sticky side of the tape is facing the platen. 4) Manually turn the left-hand spool in the clockwise direction, tightening the tape until resistance is felt. 6) Press the CODE + = (SETTING) key. 7 -6- BASIC FEATURES Selecting Pitch There are three pitches available for typing: PICA (10) : 10 characters per inch CODE + 6 ELITE (12) : 12 characters per inch CODE + 7 MICRO (15) : 15 characters per inch CODE + 8 Selecting Line Spacing There are three line spacing settings available when the appropriate key is depressed. Single line spacing CODE + 3 1 1/2 line spacing CODE + 4 Double line spacing CODE + 5 Setting Impression You can choose one of two hammer impression levels - low, high. The CODE + 2 (IMP) key is used to set the impression level. The low key is selected initially. Setting Margins You may freely adjust the margins. The minimum distance between the left and right margin is one inch. · Left Margin Move the carrier to the desired position and press the MAR L key. · Right Margin Move the carrier to the desired position and press the CODE + MAR R key. · Margin Release To move the carrier or type a character beyond margins, press the CODE + 1 (MARGIN RELEASE) key. · Hot Zone The hot zone starts six (6) spaces before the right margin. A beep will sound when the hot zone is reached. -78 Shift and Shift Lock To type uppercase characters or symbols, press either the left or right SHIFT key. For continuous uppercase typing, press the LOCK key. To release the shift lock, press the SHIFT key. Caps Lock To type the uppercase characters or lowercase symbols continuously, press the CODE + CAPS key. [. . . ] The use of non-standard supplies including Ribbons, Correction Tapes and Print Wheels, may cause poor performance or damage to your typewriter. - Please, store your typewriter in a location protected from extreme temperatures and humidity. - Be sure to unplug the typewriter before cleaning and lifting it. - If you'd like to clean your typewriter, use a mild soap to remove stains. [. . . ]