Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SOMFY INTEO EOLIS RECEIVER RTS 2. We hope that this SOMFY INTEO EOLIS RECEIVER RTS 2 user guide will be useful to you.
Lastmanuals help download the user guide SOMFY INTEO EOLIS RECEIVER RTS 2.
Manual abstract: user guide SOMFY INTEO EOLIS RECEIVER RTS 2
Detailed instructions for use are in the User's Guide.
[. . . ] INSTALLATIONguide
inteo
EOLIS receiver RTS 2
The EOLIS receiver RTS is a radio receiver for awnings with protection against wind damage. The EOLIS receiver RTS is compatible with the EOLIS sensor, all the RTS controls and the INIS RT. [. . . ] Connect the cable to the terminal.
2. Put and screw the front box.
C Wind function :
The wind threshold can be adjusted by the potentiometer to accommodate wind speeds between 10 to 50 Km/h. Principle : When the wind speed exceeds the threshold set by the EOLIS receiver RTS, after 2 seconds, an UP order is given to the motor. As long as the measured wind speed is higher than the adjusted threshold, any order from the RTS control is inhibited. When the wind speed falls below the threshold setting, a time delay of 30 seconds is activated. After this time delay any order can be given with the RTS control.
y , y , yy yy , , , , yy , ,
Mounting of the EOLIS sensor
yy , , yy , ,
The EOLIS receiver RTS is able to protect awnings against wind damage using EOLIS sensor
Wind threshold adjustment
LMN N L SC
Km/h
10
50
"S" jumper
LMN N L SC
"S" jumper : When the jumper is cut, if a down control has been given just before the wind appearance, the EOLIS receiver RTS will automatically send a down control to the motor after 12 minutes.
D Programming :
1 INITIAL INSTALLATION
with an RTS control (TELIS soliris RTS ; Centralis RTS ; TELIS 1 or 4 RTS).
Set the EOLIS receiver RTS in its programming mode by pressing the PROG button until the LED lights.
This indicates that the SOLIRIS receiver RTS is ready to receive the address of a control for one minute (After this time limit, the LED will go out).
Press shortly the programming button on the RTS control.
The LED of the EOLIS receiver RTS blinks indicating that the address of the RTS control is memorized in receiver which automatically quits its programming mode.
with an INIS RT.
Set the EOLIS receiver RTS in its programming mode by pressing the PROG button until the LED lights.
This indicates that the EOLIS receiver RTS is ready to receive the address of a control for one minute (After this time limit, the LED will go out).
1. press shortly the battery the push button
The LED of the EOLIS receiver RTS blinks indicating that the address of the INIS RT is memorized in receiver which automatically quits its programming mode.
MULTIPLE CONTROL · Assign several controls to the EOLIS receiver RTS following the same procedure as described above. You can assign up to 12 controls to one receiver. If you try to enter a 13th, your instruction will be ignored, the led of the receiver will go out.
GENERAL OR GROUP CONTROL · Set all the EOLIS receiver RTS you wish to control by one control in their programming mode and record the control following the same procedure as described above.
µ The LEDs of all the EOLIS receiver RTS blink indicating that the address of the control is memorized in all these receivers.
2 ADD A NEW CONTROL IN THE MEMORY OF A RECEIVER
(ON AN EXISTING INSTALLATION)
· To add a new control in the memory of a RTS receiver, set the EOLIS receiver RTS in its programming mode (see § D1), then press shortly the prog button of the RTS control you wish to add (to add an INIS RT, remove/replace the battery then press the front button). · It is also possible to "wake up" the EOLIS receiver RTS with another control. From a RTS control : press for more than 2 seconds on the prog button of the RTS control, then press shortly the prog button of the RTS control you wish to add (to add an INIS RT, remove/replace the battery then press the front button). From a RT control : remove/replace the battery and press the front button of the INIS RT, then press shortly the prog button of the RTS control you wish to add (to add another INIS RT, remove/replace the battery then press the front button).
3 REMOVE A RTS CONTROL FROM THE MEMORY OF THE RECEIVER
(ON AN EXISTING INSTALLATION)
· To remove a RTS control from the memory of a RTS receiver, set the EOLIS receiver RTS in its programming mode (see § D1), then press shortly the prog button of the RTS control you wish to remove (to remove an INIS RT, remove/replace the battery then press the front button). [. . . ] 1- Press the built-in manual security control of the EOLIS receiver RTS. 3- Check the good wiring of the motor and the EOLIS receiver RTS.
® [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SOMFY INTEO EOLIS RECEIVER RTS 2
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SOMFY INTEO EOLIS RECEIVER RTS 2 will begin.