User manual SONY A330LDVDKIT

[. . . ] Use a cloth lightly dampened with water for cleaning the exterior of the set. Installation Water and Moisture Do not use power-line operated sets near water ­ for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Use Power Sources This set should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local power company. For those sets designed to operate from battery power, or other sources, refer to the operating instructions. Power-Cord Protection Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the plugs, receptacles, and the point where the cord exits from the appliance. Polarization This set may be equipped with a polarized ac power cord plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. [. . . ] B For A330LDVDKIT: An audio device to the Handycam Station or your camcorder using the A/V connecting cable. C Using the internal stereo microphone (no connection required). The audio input to be recorded takes precedence over others in the order of A t B t C. You cannot record additional audio: ­ When the tape has been recorded in the 16-bit mode (p. ­ When the tape has been recorded in the LP mode. ­ When your camcorder is connected via an i. LINK cable. ­ When the tape has been recorded in 4CH MIC mode. ­ On blank sections of the tape. 78 ­ When the tape has been recorded in a TV color system other than that of your camcorder (p. ­ When the write-protect tab of the cassette is set to SAVE (p. ­ On sections recorded in HDV format. · The Active Interface Shoe has a safety device for fixing the installed external microphone (optional) securely. To connect, press down and push it to the end, and then tighten the screw. To release, loosen the screw, and then slide it out while pressing down. (You cannot specify the number of printouts. ) Preventing accidental erasure (Image protection) You can select and mark images to prevent accidental erasure. 1 Slide the POWER switch repeatedly to turn on the PLAY/ EDIT lamp. Dubbing/Editing 1 Slide the POWER switch repeatedly to turn on the PLAY/ EDIT lamp. 2 Touch [PROTECT]. t t t 2 Touch t [PRINT MARK]. t t 3 Touch the image that you want to protect. PROTECT 3 Touch the image that you want to print out later. PRINT MARK appears. 101­0002 2/ 10 101 OK appears. 4 Touch 101­0002 2/ 10 101 t [END]. OK 4 Touch t [END]. · To cancel image protection, touch the image again to cancel image protection in step 3. · To cancel Print mark, touch the image again to cancel Print mark in step 3. 81 Printing recorded images (PictBridge compliant printer) You can print out pictures using a PictBridge compliant printer without connecting the camcorder to a computer. Connect the AC Adaptor to obtain power from the wall outlet. Insert the "Memory Stick Duo" containing still images into your camcorder and turn on the printer. · You can also operate by selecting in the following orders: ­ Touch t [MENU] t (PICT. APPLI. ) t [USB SELECT] t [PictBridge PRINT] ­ Touch t [MENU] t (PICT. APPLI. ) t [PictBridge PRINT] · We cannot guarantee the operation of models that are not PictBridge compatible. Printing Connecting your camcorder to the printer 1 Select the image to be printed with / . 1 Slide the POWER switch repeatedly to turn on the PLAY/ EDIT lamp. 2 Touch t [COPIES]. 2 Connect the (USB) jack of your camcorder (DCR-HC36) or the Handycam Station (DCR-HC46/ HC96) to the printer using the USB cable. [USB SELECT] appears on the screen automatically. 3 Select the number of copies to be printed with / . A maximum of 20 copies of the image can be printed. 4 Touch t [END]. 3 Touch [PictBridge PRINT]. When connection is complete, (PictBridge connecting) appears on the screen. 3. 0M To print the date and time on the image, touch t [DATE/TIME] t [DATE] or [DAY&TIME] t . 5 Touch [EXEC] t [YES]. When printing is finished, [Printing. . . ] disappears and the image selection screen appears again. Touch [END] when printing is completed. 1 / 10 101 PictBridge PRINT 101-0001 END - + SET EXEC One of the images stored on the "Memory Stick Duo" will be displayed. · Refer also to the operating instructions for the printer to be used. · Do not attempt the following operations when is on the screen. The operations may not be performed properly. ­ Operate the POWER switch. 82 · · · · · ­ Disconnect the power cord. ­ Remove your camcorder from the Handycam Station (DCR-HC46/HC96). [. . . ] 13, 18 Pre-installed rechargeable battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Previous/Next image button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Print mark. . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]