User manual SONY AD-CEX108

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on circuit different from that to which the receiver is connected. [. . . ] -- Consult the dealer or an experienced radio/ TV technician for help. Configuration of each system ADC-WRF35 Compact disc changer, power unit & FM modulator, wired remote control and wireless remote control ADC-RF35 Compact disc changer, power unit & FM modulator and wired remote control ADC-M35 Compact disc changer CAUTION Modifications or adjustments to this product, which are not expressly approved by the manufacturer, may void the user's right or authority to operate this product. EN 2 PRECAUTIONS · Do NOT install the unit in a location where it may be subjected to: -- Direct sunlight or other sources of excessive heat -- Fluid, rain or moisture -- Excessive dirt or dust -- Excessive vibration · This unit is designed to be operated on a 12-volt DC negative-ground electrical system only. · Choose the mounting location carefully so that the unit will not interfere with normal driving functions. · Berore making connections, disconnect the ( terminal of the car battery to avoid short circuiting. · Be sure to connect the red power input lead to the positive 12-V power terminal, to which power is supplied when the ignition key is in the accessory position. · The power unit & FM modulator is designed only for this ADC-M35 compact disc changer. · Clean the discs before inserting them into the disc magazine. Always clean a disc from the center outward with a cleaning cloth. · NEVER use solvents such as benzine or alcohol to clean a disc. · You cannot play an 8-cm (3-inch) CD -- even with the specially designed adaptor. Notes on the disc magazine · Do NOT leave the disc magazine in a place subject to excessive temperature or humidity. · Do NOT insert more than one disc per slot. · Do NOT drop the disc magazine. Notes on CDs · A defective or soiled disc stored in the disc magazine can cause the sound to drop out during play. · Always handle a disc by holding its inner and outer edges. ENGLISH Reset buttons The wired remote control and compact disc changer each have a reset button. Using an unspecified connecting cable may cause background noise. · After all the connections have been completed, be sure to press either of the reset buttons on the compact disc changer or wired remote control (see page 3). · Be sure to select the output frequency and adjust the output level with the FREQUENCY SELECT switch and LEVEL control before securing the power unit & FM modulator (see page 11). · The terminals on the power unit & FM modulator for connecting the wired remote control and the supplied connecting cable look similar. Be careful not to use the wrong terminal. EN 10 Adjustments on the power unit & FM modulator FREQUENCY SELECT switch Adjusting the output level The LEVEL control on the power unit & FM modulator is set to the center position, an average level commonly used, at the factory. If necessary, adjust the level according to following these steps before securing the power unit & FM modulator in position. LEV L LEVEL control EL H Switching the frequency When sound distortion due to noise occurs, change the current position of the FREQUENCY SELECT switch to the other position (88. 7 or 89. 1 MHz) using a screwdriver or similar tool, which may eliminate the noise. The selection of the appropriate frequency must be done before securing the power unit & FM modulator in position. 88. 7 MHz FRE QUE CY S ELE CT 1 2 3 4 On your car stereo, select one of FM programs available and adjust a sound volume to the level of your preference. This volume will be used as a reference to adjust CD sound volume in step 4. Select a frequency 88. 7 or 89. 1 MHz according to the selection on the FREQUENCY SELECT switch of the power unit & FM modulator. Play a CD placed in the compact disc changer. Adjust the sound volume with the CD playing so as to match the volume adjusted in step 1. Note The radio sensitivity may be slightly reduced when the power unit & FM modulator is connected. [. . . ] Adjust the sound volume with the CD playing so as to match the volume adjusted in step 1. Note The radio sensitivity may be slightly reduced when the power unit & FM modulator is connected. In this case, turn off the compact disc changer. 89. 1 MHz Note Setting this control to maximum or to an excessively high level will cause sound distortion. EN 11 HOW TO USE How to use a compact disc magazine 1 With the label side up, insert a CD all the way. 6 discs, one in each slot To remove a CD, pull part A in the direction of the arrow as illustrated. 2 3 Disc magazine Insert the magazine (which has been taken out of the unit) firmly with the mark visible on the top side. z (eject) button To remove the magazine, press the z button and pull out the disc magazine. 4 EN 12 CD play 1 2 3 Turn on your car stereo (not supplied) and select the FM band. Select an appropriate frequency (88. 7 or 89. 1 MHz). (See page 11 for details. ) Press PWR on the wired remote control or POWER on the wireless remote control. CD play starts. 3 3 4 Adjust the sound volume on your car stereo (not supplied). Remote control Inserting the batteries insert the supplied R03 (size AAA) batteries. Be sure to match ) and ( on the batteries to the diagram inside the battery holder. Using the wireless remote control Point the wireless remote control toward remote sensor. Note · Do NOT mix new batteries with old ones. [. . . ]