User manual SONY AIR-PC10T

[. . . ] 4-134-954-11(3) Wireless Audio Transmitter for PC Operating Instructions Furthermore, if you install the supplied application software S-AIR Cast on your computer and select Remote Mode or Advanced Remote Mode, you can also control the contents on an S-AIR sub unit. For example, you can install S-AIR sub units, one in the study room and the other in the bedroom, and then install your computer with the AIR-PC10T connected in the living room. You can then listen to music from the computer by controlling the S-AIR sub unit. Connecting the system 1 Connect the cradle to your computer. 2 Plug wireless audio transmitter to the cradle. Before connecting, detach the USB cap from the wireless audio transmitter. 1 Install S-AIR Cast on your computer. [. . . ] Connected with one or more S-AIR sub unit. (Only S-AIR ID setting is made. ) Pairing is in progress. Pairing is on. About S-AIR products There are two types of S-AIR product. S-AIR main unit (this unit): This is for transmitting sound. S-AIR sub unit: This is for receiving sound (speaker, music receiver, etc. ). By connecting the AIR-PC10T to a USB port of your computer, the AIR-PC10T can transmit music stored on your computer to an S-AIR sub unit for playback. PAIRING Remote Mode In the case of high music content, operating speed may decrease. For smooth operation, 2GHz or higher CPU is recommended. Hard Disk Drive: 206MB or more (S-AIR Cast related module: 60MB / Microsoft related module: 146MB) CD-ROM or DVD drive (for software installation) Display: Screen Resolution: 1, 024 × 768 pixels (or higher), Colors: 65, 536 colors (or higher) Mouse Keyboard USB port: USB 1. 1 or 2. 0 port Sound card Software: Internet Explore 6. 0 or higher. You can connect an S-AIR sub unit wirelessly to your computer as a speaker and listen to music contents registered in iTunes or Windows Media Player by operating the S-AIR sub unit. Note that all system sounds of your computer (incoming message alerts, alarm beeps, etc. ) will also be output from the S-AIR sub unit. To use this mode, S-AIR Cast needs to be installed on your computer. User privileges 4 Click [Install S-AIR Cast] first, then click [Install Now]. Set RF change to OFF on the installed S-AIR Cast software. If the issue S-AIR Cast can be used only by users with administrator privileges. S-AIR Cast does not support the Fast User Switching function. You can connect one AIR-PC10T to a computer. You cannot connect multiple AIR-PC10T to a computer at the same time. You can use up to 10 S-AIR sub units with the AIR-PC10T. Only one playable source can be output from the S-AIR sub unit at the same time. Media Player persists after RF setting, change the S-AIR ID of the AIR-PC10T and S-AIR sub unit. For details on RF change, refer to S-AIR Cast Help. If another S-AIR main unit such as Sony's wireless home theater system using S-AIR is placed near the AIR-PC10T, turn off the power of that S-AIR main unit, or place it as far as possible from the AIR-PC10T. Check that the USB cable of the cradle is connected securely to the USB port of your computer. If the issue persists, the AIR-PC10T may be at fault. Contact your nearest Sony dealer. To stabilize S-AIR reception To use S-AIR products (AIR-PC10T and the S-AIR sub unit) Before using S-AIR products, have the following ready. Confirm the wireless transceiver on the S-AIR sub unit (if applicable) is inserted correctly. [. . . ] Stop using any equipment that generates electromagnetic waves such as a microwave oven. When in Remote Mode, remove the unplayable contents from media players (iTunes or Windows Media Player) you are using, then close the media player and restart. Turn off your computer and S-AIR sub unit, and then turn them on again. Check that headphones are not connected to the headphone jack on your computer. [. . . ]