User manual SONY AIR-SA10

[. . . ] 3-288-619-11(1) Notice for the customers in Canada For the wireless transceiver (EZW-RT10) This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Precautions Notes on use of the S-AIR product As the S-AIR product transmits sound by radio waves, sound may skip when radio waves are obstructed. This is a characteristic of radio waves and is not a malfunction. As the S-AIR product transmits sound by radio waves, equipment that generates electromagnetic energy, such as a microwave oven, may interfere with sound transmission. [. . . ] Refer to them whenever you call upon your Sony dealer regarding this product. Serial No. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For the wireless transceiver (EZW-RT10) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The connection is established between the paired unit and S-AIR main unit. Your system Neighboring system Important Safety Instructions 1) 2) 3) 4) 5) 6) 7) Read these instructions. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. This unit ID A This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated with at least 20cm and more between the radiator and person's body (excluding extremities: hands, wrists, feet and ankles). Pairing ID A S-AIR main unit ID A S-AIR main unit 1 Check that the power of the unit and the S-AIR main unit to be connected are turned on. If the issue persists, contact your nearest Sony dealer. (stereo mini jack): Accepts headphones with an impedance of 8 ohms or more Speaker section Speaker system: Full range, bass-reflex type Speaker units: 65 mm, cone type (2) Nominal impedance: 3 ohms Connecting the unit and S-AIR main unit is not possible. (The S-AIR indicator flashes. ) Wireless transceiver (EZW-RT10) Setting the clock 1 Turn on the unit. Press . Changing the display To change the information on the display while the unit is on Press DISPLAY . Each time you press the button, the display changes as follows: When the unit is connected to an S-AIR main unit: 6 Press / repeatedly to select the desired option. AUTO: Sound from the connected S-AIR main unit is output. However, an alarm sounds in the following cases. When communication with the S-AIR main unit is cut off. When no sound is output from the S-AIR main unit or the audio signal level is too low. When the S-AIR main unit is not ready for playback at the set start time. [. . . ] Change the S-AIR ID settings of the unit and the SAIR main unit. Turn off the unit and S-AIR main unit and then turn them on again. Check that the power cord is connected securely and the unit is turned on. Check that headphones are not connected to the (headphone) jack on the rear of the unit. [. . . ]