User manual SONY AVD-V500

[. . . ] aiwa AV-DV500 STEREO RECEIVER OPERATING INSTRUCTIONS Precautions pg. 1 WARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture "CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO QUALIFIED SERVICE PERSONNEL. " Explanation of Graphical Symbols: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's inclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Owner's record For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. [. . . ] To listen to or watch Tape Radio Record Television, etc. Compact Disc Video (VCR or LD) MD DVD TUNER PHONO AUX/TVa CD VIDEO 1, VIDEO 2/5 CHa, VIDEO 3 VIDEO 2/5 CHa VIDEO 2/5 CH The button pressed TAPE MONITOR a) For selecting AUX/TV, or VIDEO 2/LD/MD, see "To change a displayed name for the AUX/TV button and VIDEO 2/5 CH button" of "BEFORE OPERATION" (see page 6). NOTE When using a turntable with a built-in equalizer amplifier, set the switch of the equalizer amplifier to off. See the instructions of the turntable for further information. About the video source to the monitor or TV V1: VIDEO 1, V2: VIDEO 2, V3: VIDEO 3 The selected video source is indicated on the display and the video signal through the MONITOR VIDEO OUT jack is output on the TV. RECORDING AN AUDIO SOURCE 1 Select the program source to be recorded. 2 Set the tape deck or MD recorder to the recording mode. To monitor recorded sound during recording (when the connected tape deck is a three-head system) Press the TAPE MONITOR button. "TAPE ON" appears on the display for four seconds, and then the source name selected in step 1 comes back on. To cancel the tape monitor, press it again so that "TAPE oFF" appears. NOTE Any sound control except the BBE system has no effect on recording (see page 7). TO PLAY A DVD RECORDED IN DOLBY DIGITAL SURROUND This receiver has 5 ch connectors supporting Dolby Digital decoder with the 5. 1 ch output terminals. When a DVD player, such as Aiwa XD-DV500, that contains a Dolby Digital decoder is connected to the receiver, you can enjoy theater-quality audio right in your home when playing discs recorded in Dolby Digital Surround. Preparation In the initial settings of the DVD player, set the SUBWOOFER mode of SETUP SPEAKERS to OFF. For details, see the initial settings in the instruction manual of the DVD player. 1 Press the VIDEO 2/5 CH button to select the VIDEO 2 function. "5 CH" appears on the display and the 5 CH surround is turned on. 3 Start playing the DVD recorded in Dolby Digital Surround. To turn off the 5 CH surround, press the VIDEO 2/5 CH button once more. NOTE · The DOLBY PRO LOGIC, BBE, or DSP system is automatically canceled when the 5 CH surround is turned on. · See page 13 when adjusting the sound level of the center and surround speakers. RADIO RECEPTION pg. 10 MANUAL TUNING 1 Press the TUNER button repeatedly to select the desired band. When the TUNER button is pressed while the power is off, the power is turned on directly. 2 Press the UP or DOWN button to select a station. Each time the button is pressed, the frequency changes. [. . . ] DOLBY PRO LOGIC Manufactured under license from Dolby Laboratories Licensing Corporation. "DOLBY" the double-D symbol Corporation. and "PRO LOGIC" are trademarks of Dolby Laboratories Licensing GENERAL (cont. ) pg. 16 TROUBLESHOOTING GUIDE If the unit fails to perform as described in these Operating Instructions, check the following guide. GENERAL There is no sound. [. . . ]