User manual SONY AX4000

[. . . ] Operating Instructions Getting Started Operating the Remote Commander Unit Settings Setting by On-Remote Setup Additional Information Appendix RM-AX4000 Integrated Remote Commander To go to the section you want to read, click the title in the PDF Bookmarks, the title in the "Table of Contents" of the Operating Instructions, or the page in the sentences. © 2005 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNING You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTICE FOR THE CUSTOMERS IN THE U. S. A. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Each time the (­)/(+) key is pressed, the level decreases/increases by 1. or "LIGHT" appears as the Display title. SU LEARN NG LIGHT 8 Press the BACK button or the COMMANDER OFF button. BACK COMMANDER OFF or OFF_TIME LEVEL FADE ON_MODE "LIGHT" appears as the Display title. SU Note When you set the automatic-off time to longer than 10 seconds (factory setting), the battery life may be shorter. LEARN NG LIGHT Unit Settings 6 Press "LEVEL" on the Label keys. LEVEL OFF_TIME LEVEL FADE ON_MODE 9 Press "FADE" on the Label keys. The setting display for brightness appears. SU FADE LEARN NG LIGHT The setting display for fade effect appears. The current setting is shown inside the [ ], while the other flashes. SU LEVEL (-) LEVEL 15 (+) LEARN NG LIGHT FADE [ ON ] OFF Continued 35 Setting the backlight (continued) 13 Press the LIGHT or ALL key to select which buttons activate the backlight. LIGHT: The backlight is activated by pressing the LIGHT button only. ALL: The backlight is activated by pressing any button on the Remote Commander except the VOLUME +/­, CHANNEL +/­ and COMMANDER OFF buttons. The buttons to activate backlight changes and a beep sounds each time you press the keys. Note In the "ALL" position, if you use the Remote Commander frequently, the battery life may be shorter. In this case, shorten the automatic-off time. 10 Press the ON or OFF key to select the fade effect of the backlight. ON: fade in/out backlight OFF: normal backlight The fade effect of the backlight changes and a beep sounds each time you press the keys. 11 Press the BACK button or the COMMANDER OFF button. BACK COMMANDER OFF or "LIGHT" appears as the Display title. SU LEARN NG LIGHT 14 Press the BACK button or the COMMANDER OFF button. BACK COMMANDER OFF or OFF_TIME LEVEL FADE ON_MODE "LIGHT" appears as the Display title. SU LEARN NG LIGHT 12 Press "ON_MODE" on the Label keys. ON_MODE OFF_TIME LEVEL FADE ON_MODE The setting display for buttons to activate the backlight appears. The current setting is shown inside the [ ], while the other flashes. SU 15 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF LEARN NG LIGHT The Remote Commander turns off. ON_MODE LIGHT [ ALL ] 36 If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The previous status returns, and the Remote Commander turns off. Setting the LCD display Setting the automatic-off time of the LCD display The Remote Commander (RM-AX4000) is preset at the factory to switch off the LCD display automatically if you do not operate it for more than 10 minutes. To change this setting, perform the following procedure. If you want to return to the previous display Press the BACK button or the COMMANDER OFF button, the previous LCD display returns. 1 While pressing the COMMANDER OFF button, press the MUTING button. COMMANDER OFF Unit Settings MUTING "SET" appears as the Display title. SU LEARN NG SET LIGHT DISPLAY OTHER If "DISPLAY" does not flash on the Label keys, press the Display title (SET) repeatedly until it appears. Continued 37 Setting the LCD display (continued) 5 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF 2 Press "DISPLAY" on the Label keys. DISPLAY The Remote Commander turns off. "DISPLAY" appears as the Display title. SU If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The previous status returns, and the Remote Commander turns off. LEARN NG DISPLAY If you want to return to the previous display DISP-OFF ALIGN CONTRAST Press the BACK button or the COMMANDER OFF button, the previous LCD display returns. 3 Press "DISP-OFF" on the Label keys. DISP-OFF The setting display for automatic-off time of the LCD display appears. SU LEARN NG DISPLAY DISP-OFF (-) 10min (+) 4 Press the (­) or (+) key to change the automatic-off time of the LCD display. You can set the automatic-off time from 1 to 30 minutes. Each time the (­)/(+) key is pressed, the minute decreases/increases by 1 minute. For example, "02min" on the Label keys means 2 minutes. 38 Calibrating the alignment of the LCD display You can calibrate the alignment of the LCD display if the Touch-keys are not working properly. To change this setting, perform the following procedure. 3 Press the point on the top-right of the LCD display. The square appears in the center of the LCD display. SU LEARN NG ALIGNMENT 1 While pressing the COMMANDER OFF button, press the MENU button and EXIT button. COMMANDER OFF MENU EXIT 4 Press the square in the center of the LCD display. When the calibration is complete, the beep sounds, and the LCD display returns to the selecting display of display setting. SU The setting display for calibrating the alignment of the LCD display appears. SU Unit Settings LEARN NG ALIGNMENT LEARN NG DISPLAY DISP-OFF ALIGN CONTRAST Note 2 Press the point on the bottom-left of the LCD display. The other point appears on the topright of the LCD display. SU When calibrating, be sure to press the point accurately, otherwise the calibration will be off and you will need to start over. 5 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF LEARN NG ALIGNMENT The Remote Commander turns off. If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The Remote Commander turns off. Continued 39 Setting the LCD display (continued) 3 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF Setting the contrast of the LCD display You can adjust the contrast of the LCD display if the screen is not viewed properly. To change this setting, perform the following procedure. The Remote Commander turns off. If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The previous status returns, and the Remote Commander turns off. 1 While pressing the COMMANDER OFF button, press the OK button. COMMANDER OFF OK The setting display for contrast appears. SU LEARN NG CONTRAST A/B POWER 1 4 7 +10 2 5 8 0 3 6 9 ENTER TOP MENU REC DISPLAY MAIN/SUB INPUT LIST 2 Press the CHANNEL +/­ button to adjust the contrast of the LCD display. CHANNEL You can set the contrast level from 1 to 15. CHANNEL +: Darker contrast CHANNEL ­: Lighter contrast Note If you press the CHANNEL +/­ button and the contrast level is already at the minimum/maximum level, the beep does not sound. The level can be set from 1 to 15. 40 Setting the beep The Remote Commander (RM-AX4000) is preset at the factory with the confirmation beep set to on. To change this setting, perform the following procedure. 3 Press "BEEP" on the Label keys. BEEP The setting display for beep appears. The current setting is shown inside the [ ], while the other flashes. SU 1 While pressing the COMMANDER OFF button, press the MUTING button. COMMANDER OFF LEARN NG OTHER MUTING BEEP [ ON ] OFF "SET" appears as the Display title. SU LEARN NG SET 4 Press the ON or OFF key to select the beep. ON: Turns on the beep. The beep setting changes and a beep sounds each time you press the key. Unit Settings LIGHT DISPLAY OTHER If "OTHER" does not flash on the Label keys, press the Display title (SET) repeatedly until it appears. 5 Press and hold the COMMANDER OFF button for more than 2 seconds. COMMANDER OFF 2 Press "OTHER"on the Label keys. OTHER The Remote Commander turns off. "OTHER" appears as the Display title. SU LEARN NG OTHER If you want to quit before finishing Press and hold the COMMANDER OFF button for more than 2 seconds. The previous status returns, and the Remote Commander turns off. BEEP DS_TIME CLOCK RESET If you want to return to the previous display Press the BACK button or the COMMANDER OFF button, the previous LCD display returns. 41 Adjusting the clock You can adjust the clock after setting. [. . . ] To change the time display To call up the setting up menu Slow playback in the reverse direction Slow playback in the forward direction To go into the repeat mode To change the playback mode To switch the edit mode to on/off To change a disc To search in the reverse direction To search in the forward direction Appendix * The Z key does not work unless pressed for more than 1 second (factory setting). Continued 79 Table of preset functions (continued) VCR (Video Cassette Recorder) KEY DISPLAY POWER FUNCTION To turn the power on/off KEY DISPLAY SP/LP H. S. REW COUNTER ANT/SW TSEARCH SEARCHt LINE1 LINE2 DV_IN TV_TUNER FUNCTION To switch the tape speed To rewind at high speed To change the counter display To switch the antenna output REVIEW locked picture search CUE locked picture search To select the input source: LINE 1 To select the input source: LINE 2 To select the input source: DV To return to the TV (to reset the external input) 1 ­ 9, 0, ENTER To change the channel (To change to channel 5, for example, press 0 and 5, or press 5 and ENTER. ) m N M REC* x X DISPLAY MAIN/SUB Z*2 INPUT ·t F f g G OK MENU EXIT VOLUME + VOLUME ­ CHANNEL + CHANNEL ­ MUTING 1 To rewind To play To fast-forward To record To stop To pause To activate the on-screen display To switch the sound of the duplex broadcast To eject a cassette To change the input mode CM skip function To move the cursor upward To move the cursor downward To move the cursor to the right To move the cursor to the left To enter the selection of the MENU display To call up the MENU To exit the MENU Volume up (TV) Volume down (TV) Channel up Channel down To mute the volume on the TV. To play at double speed To select the recording time by 30 minutes and begin recording *1 To avoid accidental recording, the REC key does not work unless pressed for more than 1 second (factory setting). *2 The Z key does not work unless pressed for more than 1 second (factory setting). PLAY x2 Q. TIMER 80 DVR (Digital Video Recorder) KEY DISPLAY POWER FUNCTION To turn the power on/off KEY DISPLAY EPG*1 MENU EXIT TOOLS VOLUME + VOLUME ­ CHANNEL + CHANNEL ­ MUTING FUNCTION To use the program guide To call up the MENU To exit the MENU To go into the OPTION setting mode Volume up (TV) Volume down (YV) Channel up Channel down To mute the volume on the TV. To select the channel previously selected To replay, or to go into REC/ REVIEW mode during play (After about 5-second rewind, replay begins. ) To bring up Master Guide To switch the antenna output Page down Page up To select the desired recorded program (It is necessary to have recorded the desired program. ) To select the desired recorded program (It is necessary to have recorded the desired program. ) Category guide To return to the home display from any display To display a drop menu and toggle to change the user 1 ­ 9, 0, ENTER To change the channel (To change to channel 5, for example, press 0 and 5, or press 5 and ENTER. ) · INFO m N M S. INDEX REC*2 x X DISPLAY . [. . . ]