User manual SONY BDV-E301

[. . . ] Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior. Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. [. . . ] If the TV is not compatible with the Control for HDMI - Easy Setting function, set the Control for HDMI function of the system and TV manually. Note · For details on setting the TV, refer to the operating instructions of the TV. 1 2 3 Make sure that the system and the TV are connected with an HDMI cable. Turn on the TV and press [/1 to turn on the system. Set the Control for HDMI function of the system and TV. The Control for HDMI function for the system and TV is simultaneously set to on. To set the [Control for HDMI] function of the system to on/off manually 1 2 3 4 Press HOME. The home menu appears on the TV screen. Press C/c to select [Setup]. Press X/x to select [System Settings], then press . Press X/x to select [HDMI Settings], then press . TV BRAVIA Sync 1 Note 2 3 The [HDMI Settings] display appears. · Depending on the connected component, the Control for HDMI function may not work. Refer to the operating instructions supplied with the component. 5 Press X/x to select [Control for HDMI], then press . 44GB 6 Press X/x to select the setting, then press . · [On]: On. · [Off]: Off. Enjoying TV sound from the speakers in this system (System Audio Control) You can simplify operation to enjoy TV sound via this system. To use this function, connect the system and the TV with an audio cord and an HDMI cable (pages 20, 21). You can use the System Audio Control function as follows: · When the system is turned on, TV sound can be output from the speakers of the system. · When TV sound is output from the speakers of the system, you can change the output method to the speakers of the TV via the TV menu. · When TV sound is output from the speakers of the system, you can adjust the volume and turn off the sound of the system using the TV remote. Note Turning the system off in sync with the TV (System Power Off) When you turn the TV off by using the POWER button on the TV's remote or TV "/1 on the system's remote, the system turns off automatically. Note · This function depends on the settings of your TV. For details, refer to the operating instructions of the TV. Other Operations Watching BD/DVD by a single button press (One-Touch Play) Press ONE-TOUCH PLAY. The system and your TV turn on, your TV's input is set to the HDMI input to which the system is connected, and the system starts playing a disc automatically. The result is implemented. x The measurement is not OK. If you do not connect center or surround speakers, set the parameters for [Center] and [Surround]. Since the front speaker and subwoofer settings are fixed, you cannot change them. When you use the Wireless Surround Speaker Kit (WAHT-SBP2, optional) for the surround back speakers (page 14), set [Surround Back] also. [Front] Other Operations [Yes] [Center] Follow the message, then select [OK] to retry. Note [Yes]: Normally select this. [None]: Select this if no center speaker is used. [Surround] · While the Auto Calibration function works: ­ do not turn off the power. ­ do not disconnect the calibration mic. [Yes]: Normally select this. [None]: Select this if no surround speaker is used. [Surround Back] [Yes]: Select this if surround back speakers are used. [None]: Select this if no surround back speakers is used. [Subwoofer] Setting the Speakers [Speaker Settings] To obtain the best possible surround sound, set connection of the speakers and their distance from your listening position. Then use the test tone to adjust the level and the balance of the speakers to the same level. [Yes] x [Distance] When you move the speakers, be sure to set the parameters of the distance (A) from the listening position to the speakers. You can set the parameters from 0. 0 to 7. 0 meters. 47GB The speakers in the illustration correspond to the following: 1Center speaker 2Front left speaker (L) 3Front right speaker (R) 4Subwoofer 5Surround left speaker (L) 6Surround right speaker (R) 7Surround back left speaker (L) (optional) 8Surround back right speaker (R) (optional) [Surround Back Left/Right]* 0. 0 dB: Set the surround back speaker level. [Subwoofer] 0. 0 dB: Set the subwoofer level. * This item appears when you set it to [Yes] in the [Connection] setting. x [Test Tone] The speakers will emit a test tone to adjust [Level]. [Off]: The test tone is not emitted from the speakers. [. . . ] The re-recordable feature makes extensive editing and time-shifting applications possible. Developed as an extension to Dolby Digital, the audio coding technology supports 7. 1 multichannel surround sound. 71GB Dolby Pro Logic II DTS-HD Master Audio Dolby Pro Logic II creates five full-bandwidth output channels from 2 channel sources. This is done using an advanced, high-purity matrix surround decoder that extracts the spatial properties of the original recording without adding any new sounds or tonal colorations. x Movie mode DTS-HD Master Audio has a maximum transmission rate of 24. 5 Mbps, and uses lossless compression, and DTS-HD Master Audio corresponds to a maximum sampling frequency of 192 kHz, and maximum of 7. 1ch. HDMI (High-Definition Multimedia Interface) The Movie mode is for use with stereo television shows and all programs encoded in Dolby Surround. The result is enhanced sound field directionality that approaches the quality of discrete 5. 1-channel sound. Dolby Surround Pro Logic As one method of decoding Dolby Surround, Dolby Surround Pro Logic produces four channels from 2 channel sound. Compared with the former Dolby Surround system, Dolby Surround Pro Logic reproduces left-to-right panning more naturally and localizes sounds more precisely. [. . . ]