User manual SONY BDV-HZ970W

[. . . ] 4-187-302-11(1) Blu-ray Disc/DVD Home Theatre System Operating Instructions BDV-HZ970W / IZ1000W ©2010 Sony Corporation WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. [. . . ] The result is implemented. Other Operations x The measurement is not OK. Follow the message, then select [OK] to retry. Note 6 7 Press X/x to select [OK]. To cancel, select [Cancel]. Press . [Auto Calibration] starts. The system adjusts the speaker settings automatically. For proper calibration results, please remain quiet during the measurement. Note · While the Auto Calibration function works: ­ do not turn off the power. ­ do not disconnect the calibration mic. Setting the Speakers [Speaker Settings] To obtain the best possible surround sound, set connection of the speakers and their distance from your listening position. Then use the test tone to adjust the level and the balance of the speakers to the same level. · Before [Auto Calibration], make sure that the surround amplifier turns on and you install the surround amplifier in the appropriate location. If you install the surround amplifier in an improper location, such as another room, proper measurement will not be obtained. · When you use the Wireless Surround Speaker Kit (WAHT-SBP2, optional) for the surround back speakers (page 17), install the speakers in appropriate location and turn the surround amplifier on. To use the surround back speakers, set [Surround Back] in [Speaker Settings] to [Yes] (page 54) 1 2 3 4 Press HOME. The home menu appears on the TV screen. Press C/c to select [Setup]. Press X/x to select [Audio Settings], then press . Press X/x to select [Speaker Settings], then press . The [Speaker Settings] display appears. 53US 5 Press X/x to select the item, then press . Check the following settings. x [Connection] 2 1 3 4 If you do not connect center or surround speakers, set the parameters for [Center] and [Surround]. Since the front speaker and subwoofer settings are fixed, you cannot change them. When you use the Wireless Surround Speaker Kit (WAHT-SBP2, optional) for the surround back speakers (page 17), set [Surround Back] also. [Front] A 5 6 7 A 8 [Yes] [Center] [Yes]: Normally select this. [None]: Select this if no center speaker is used. [Surround] [Yes]: Normally select this. [None]: Select this if no surround speaker is used. [Surround Back] [Front Left/Right] 10 ft/3. 0 m: Set the front speaker distance. [Center]* 10 ft/3. 0 m: Set the center speaker distance. [Surround Left/Right]* 10 ft/3. 0 m: Set the surround speaker distance. [Surround Back Left/Right]* 10 ft/3. 0 m: Set the surround back speaker distance. [Subwoofer] 10 ft/3. 0 m: Set the subwoofer distance. * This item appears when you set it to [Yes] in the [Connection] setting. Note [Yes]: Select this if surround back speakers are used. [None]: Select this if no surround back speakers is used. [Subwoofer] · Depending on the input stream, [Distance] may not be effective. Tip [Yes] x [Distance] · You can change measurement units (feet or meters) by pressing the color button (RED). When you move the speakers, be sure to set the parameters of the distance (A) from the listening position to the speakers. You can set the parameters from 0 to 23 feet (0. 0 to 7. 0 meters). The numbers in the illustration indicate the following: 1Center speaker 2Front left speaker (L) 3Front right speaker (R) 4Subwoofer 5Surround left speaker (L) 6Surround right speaker (R) 7Surround back left speaker (L) (optional) 8Surround back right speaker (R) (optional) x [Level] You can adjust the sound level of the speakers. You can set the parameters from ­6. 0 dB to +6. 0 dB. Be sure to set [Test Tone] to [On] for easy adjustment. [. . . ] To take full advantage of Dolby Surround Pro Logic, you should have one pair of surround speakers and a center speaker. The surround speakers output monaural sound. Dolby TrueHD Dolby TrueHD is a lossless coding technology that supports up to 8 channels of multi-channel surround sound for the next generation of optical discs. The reproduced sound is true to the original source bit-for-bit. DTS HD Digital Cinema Sound (HD-D. C. S. ) is Sony's new innovative home theater technology using the latest acoustic and digital signal processing technologies. It is based on precise response measurement data of a mastering studio. [. . . ]