User manual SONY BDV-T28 INSTALLATION GUIDE

[. . . ] Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. Indoor use only. This marking is located on the laser protective housing inside the enclosure. This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior. Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems) This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. [. . . ] Each time you press the button, the system tunes in one preset station. · You can select the preset station number directly by pressing the number buttons. Tuner Receiving RDS broadcasts Simply select a station from the FM band. When you tune in a station that provides RDS services, the station name* appears in the front panel display. * If an RDS broadcast is not received, the station name may not appear in the front panel display. · RDS may not work properly if the station you are tuned to is not transmitting the RDS signal properly, or if the signal strength is weak. · Not all FM stations provide RDS service, nor do they provide the same type of services. If you are not familiar with the RDS system, check with your local radio stations for details on RDS services in your area. · While receiving an RDS broadcast, each time you press DISPLAY, the display in the front panel display changes as follows: Station name t Frequency t Preset number t Stream information/Decoding status* t Station name t . . . * Does not appear depending on the setting of [Surround Setting]. 35GB Other Operations Using the Control for HDMI Function for "BRAVIA" Sync This function is available on TVs with the "BRAVIA" Sync function. By connecting Sony components that are compatible with the Control for HDMI function via an HDMI cable, operation is simplified. · Some functions can only be used if the connected TV is compatible, and require prior setting via the TV. Refer to the operating instructions of the TV. · To use the System Audio Control function, you need to make an audio connection between the system and TV (page 14). You can use the System Audio Control function as follows: · When the system is turned on, the sound of the TV or other components can be output from the speakers of the system. · When sound from the TV or other components is output via the speakers of the system, you can change the speakers to which TV sound is output by pressing SPEAKERS TVyAUDIO. · When sound from the TV or other components is output via the speakers of the system, you can adjust the volume and turn off the sound of the system by operating the TV. · While the TV is in PAP (picture and picture) mode, or the system is playing video/photo files from the iPod/iPhone, the System Audio Control function will not work. The child lock function is activated and the buttons on the unit are locked. (You can operate the system by using the remote. ) To cancel, press x for more than 5 seconds so that "UNLOCK" appears in the front panel display. · When you operate the buttons on the unit while the child lock function is on, "LOCKED" flashes in the front panel display. Using the Sleep Timer You can set the system to turn off at a preset time, so you can fall asleep listening to music. The time can be preset in intervals of 10 minutes. Press SLEEP. Controlling Your TV with the Supplied Remote By adjusting the remote signal, you can control your TV with the supplied remote. · When you replace the batteries of the remote, the code number may reset itself to the default (SONY) setting. Reset the appropriate code number. Each time you press SLEEP, the minutes display (the remaining time) in the front panel display changes by 10 minutes. When you set the sleep timer, the remaining time appears every 5 minutes. When the remaining time is less than 2 minutes, "SLEEP" flashes in the front panel display. Preparing the remote for controlling the TV Press and hold TV "/1 while entering your TV's manufacturer's code (see the table) using the number buttons. Then release TV "/1. To check the remaining time Press SLEEP once. To change the remaining time Press SLEEP repeatedly to select the desired time. If the setting is unsuccessful, the currently registered code is not changed. Re-enter the code number. 38GB Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the code that works with your TV. Manufacturer Code number Browsing Websites You can connect to the Internet and enjoy websites like the Sony homepage using the system. SONY LG PANASONIC PHILIPS SAMSUNG TOSHIBA 01 (default) 05 06 02, 03, 07 02, 08 04 1 2 3 4 Prepare for Internet browsing. Connect the system to a network (page 19). Press HOME. The home menu appears on the TV screen. Press C/c to select [Network]. Press X/x to select [Internet Browser], then press . Other Operations The [Internet Browser] display appears. Changing the Brightness of the Front Panel Display Press DIMMER. · Some websites may not display correctly, or not function. To enter a URL Select [URL entry] from the options menu. Enter the URL using the software keyboard, then select [Enter]. Each time you press DIMMER, the brightness of the front panel display is changed. To set the default start page Saving Power in Standby Mode Check that the following settings are both made: ­ [Control for HDMI] in [HDMI Settings] is set to [Off] (page 49). ­ [Quick Start Mode] is set to [Off] (page 49). While the page you want to set is displayed, select [Set as start page] from the options menu. To return to the previous page Select [Previous page] from the options menu. If the previous page does not appear even if you select [Previous page], select [Window List] from the options menu and select the page you want to return to from the list. To quit Internet Browser Press HOME. 39GB Internet Browser display You can check website information by pressing DISPLAY. [. . . ] If the detected even if [Scan] is desired wireless router is still not detected, press RETURN to select [Manual performed. The system cannot connect to the · The distance between the unit and the wireless LAN router is too far (page 19). network or the network connection is unstable. 57GB Additional Information Playable Discs Blu-ray Disc DVD3) Note on playback operations of a BD/DVD Some playback operations of a BD/DVD may be intentionally set by software producers. Since this system plays a BD/DVD according to the disc contents the software producers designed, some playback features may not be available. BD-ROM1) BD-R/BD-RE2) DVD-ROM DVD-R/DVD-RW DVD+R/DVD+RW CD-DA (Music CD) CD-ROM CD-R/CD-RW Super Audio CD CD3) Note about double-layer BDs/ DVDs The playback picture and sound may be momentarily interrupted when the layers switch. 1)Since the Blu-ray Disc specifications are new and evolving, some discs may not be playable depending on the disc type and the version. [. . . ]