User manual SONY BKDS9470 INSTALLATION MANUAL

[. . . ] SWITCHER PROCESSOR PACK DVS-9000-C DVS9000SF-C PRODUCTION SWITCHER PROCESSOR DVS-9000 DVS-9000SF HK-PSU04 BKDS-9160 BKDS-9161 BKDS-9162 BKDS-9210 BKDS-9470 MKS-8110SD MKS-8111SD BZS-9250 BZS-9420 INSTALLATION MANUAL 1st Edition (Revised 2) !WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! [. . . ] Checks on Completion of Installation 3. MY-108 board (DVS-9000/9000SF) A 1 E106 2 TP104 D114 TP103 D113 TP101 D104 TP102 D103 E100 B C D E F G H J K L M E107 N P R 3 E105 4 E101 5 SL700 SL701 SL702 CN700 E104 TP604 TP602 E108 TP209 TP205 TP206 TP208 D702 D703 D704 D700 D200 D701 TP207 CN401 S100 TP400 E103 TP1502 E109 6 7 8 9 S400 10 11 E110 TP202 TP203 TP200 TP201 E102 TP204 12 13 A side/Component side <LED> D103, D107 (A-4) : +1. 8 V-1 and 2 +1. 8 V-1 and 2 power supply status indication. Lit when the +1. 8 V-1 and 2 power are supplied. D113 (A-3) : +3. 3 V +3. 3 V power supply status indication. D114 (A-3) : +12 V +12 V power supply status indication. If this LED does not light, the fuse may have blown. D200 (A-11) : PLL UNLOCK status LED Indicates lock/unlock of the PLL (Phase Locked Loop) in the FPGA. If this LED lit, the PLL can possibly be unlocked. D700 (A-10) : DLL UNLOCK status LED Indicates lock/unlock of the DLL (Delay Locked Loop) in the FPGA. If this LED lit, the DLL can possibly be unlocked. ERROR status LED Indicates the configuration error of the FPGA. If this LED lit, the FPGA can possibly be working incorrectly. D702, D703, D704 (A-10) : C2, C1 and C0 status LED Indicates the status of CPU on the circuit board. <Switch> S100 (A-8) : MY-CPU reset switch Pressing this switch initializes the CPU on the MY-108 board. 1-20 DVS-9000/9000SF 1-8. Checks on Completion of Installation S400 (A-9) : MONITOR reset switch The reset switch that is used to reset the monitor during maintenance through the terminal. <Slit land> SL700, SL701 (A-5), SL702 (A-6) :JTAG Chain switching They are the slit lands that are used to switch the JTAG chains. Connect these slit lands to open or to close them so that the following statuses can be obtained. SL700 SL701 SL702 Status Short Open Open Open Short Short The chain of CPLD only is established. All of the JTAG devices are connected in chain. TP202 (P-12) : FLOE (Field Odd Even) signal check terminal FLOE signal measuring terminal. TP203 (P-12) : CKX (control timing) signal check terminal CKX signal measuring terminal. TP204 (P-12) : VH CLK signal check terminal VH CLOCK signal measuring terminal. TP205 (P-9) : VDO signal check terminal VDO signal measuring terminal. TP206 (N-9) : HDO signal check terminal HDO signal measuring terminal. TP207 (P-9) : FDO signal check terminal FDO signal measuring terminal. [. . . ] (Refer to Section 1-4. ) Connect it correctly. YES NO Are the input and output cables connected correctly? Check connections of the input and output equipment. The power supply unit is probably defective. YES Is the Software installed correctly? NO Install the software correctly. (Refer to the User's Guide. ) The main power of the DVS-9000SF cannot be turned on. (Indicator does not light green. ) The main power of the DVS-9000SF cannot be turned on. (Indicator does not light green. ) YES The DVS-9000/9000SF is probably defective. Is the POWER switch A of the DVS-9000SF turned ON? [. . . ]