User manual SONY BKM-120D

[. . . ] SDI 4:2:2 Input Adaptor BKM-120D NTSC/PAL Input Adaptor BKM-127W Analog Input Adaptor BKM-128WX Analog Component Input Adaptor BKM-129X HD SDI Input Adaptor BKM-142HD SDTI-CP/SDI Input Adaptor BKM-150CP DV Input Adaptor BKM-155DV INSTALLATION MANUAL 1st Edition (Revised 8) [Japanese/English] · · · · BKM-120D SDI 4:2:2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3(J) BKM-127W NTSC/PAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5(J) BKM-128WX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7(J) BKM-129X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Even if you do not wish to use loop-through output, you need not attach the 75-ohm termination to connectors 2 and 4. Input of YC signals You can input YC signals to connector 5 and obtain loop-through output of the signals from connector 6. Even if you do not wish to use loop-through output, you need not attach the 75-ohm termination to connector 6. 5 (E) BKM-127W NTSC/PAL Input Adaptor Assigning input signals to connectors Before inputting signals to the BKM-127W, you must specify the type and format of the signal that will be input to each connector. For information about the signal assignment, refer to the manual of your video monitor. Signal characteristics Analog composite, YC signals Signal level Analog composite 1 Vp-p +3 dB/­6 dB YC Y: 1 Vp-p ±6 dB C: 0. 286 Vp-p ±6 dB (NTSC burst signal level) 0. 3 Vp-p ±6 dB (PAL burst signal level) Luminance signal Frequency characteristics Analog composite Monochrome signal: 50 Hz to 6 MHz ±2 dB Color signal: ­30 dB relative to subcarrier frequency YC Y: 50 Hz to 6 MHz ±2 dB Chrominance signals Demodulation axis R­Y/B­Y Subcarrier synchronization range ±200 Hz min. Chroma phase adjustment range (NTSC) ±10° min. Signal assignment is not necessary for the LMD series monitors. Note After assigning input signals to each connector, carry out AUTO adjustment in the CONTROL PRESET ADJ menu. Specifications General Power requirements +5 V, ±6 V Power consumption 3 W Operating conditions Temperature 0°C to 35°C (32°F to 95°F) Optimum temperature 20°C to 30°C (68°F to 86°F) Humidity 0% to 90% (no condensation) Pressure 700 hPa to 1060 hPa Storage and transport conditions Temperature ­10°C to 40°C (14°F to 104°F) Humidity 0% to 90% Pressure 700 hPa to 1060 hPa Maximum external dimensions 25 × 162 × 122 mm (1 × 61/2 × 47/8 inches) (1-slot size) Mass 270 g (10 oz) Accessories supplied Installation Manual (1) Design and specifications are subject to change without notice. Input/output connectors Analog composite signals BNC × 2, high impedance, with loop-through output and 75-ohm automatic termination YC signals 4-pin mini DIN × 1, with loop-through output and 75ohm automatic termination 6 (E) BKM-128WX Analog Input Adaptor The BKM-128WX Analog Input Adaptor is a video signal input adaptor for Sony LCD monitors. When installed in the optional input slot of a monitor, it provides video input and output connectors for the monitor. For the monitors in which the BKM-128WX can be installed, see the chart on page 1 (E). Note Using the Input and Output Connectors For how to install the BKM-128WX in the optional input slot on a monitor, refer to the operating instructions of the monitor in which the adaptor is installed. When you install the BKM-128WX into the LMD151MD or LMD-181MD monitor, use the monitor whose serial number is given in the table below. If installing the BKM-128WX into the monitor with an earlier serial number, contact Sony Service. Model LMD-151MD LMD-181MD Serial number 2000461 or later 2000801 or later Configuration of input/output connectors and signals that may be input Analog composite signals ANALOG 1 2 IN IN Y/G 5 6 7 8 Y/G 1 OUT OUT IN IN PB/B PB/B Functions Analog composite/YC input and output signal connectors YC 2 OUT OUT IN 9 q; qa qs PR/R 3 4 IN PR/R The BKM-128WX is equipped with one input and one output connectors for analog signals and one input and one output connectors for YC signals. The adaptor is equipped with a decoder for analog composite NTSC and PAL signals. 2 OUT OUT IN SYNC SYNC OUT Analog RGB/component and external sync input and output signal connectors The BKM-128WX is equipped with one input and one output connectors for analog RGB/component signals and one input and one output connectors for EXT SYNC signals. 128WX Automatic termination (only terminals with the mark) Aperture enhance function As the resolusion is converted when monitoring an NTSC/PAL signal on an LCD monitor, the picture outline becomes softer. The BKM-128WX enhances the picture outline to provide a sharper picture. The function is related with the setting of the menu on the LMD-181MD/151MD LCD monitors. The function does not work for the RGB/component input signals. Input of analog composite and YC signals You can input analog composite signals to connector 1 and YC singnals to connector 3. When the cable is connected to connectors 2 and 4, the 75-ohm termination of connectors 1 and 3 is automatically released and you can obtain the loop-through output from connectors 2 and 4. Even if you do not wish to use loop-through output, you need not attach the 75ohm termination to connectors 2 and 4. Input of Y/PB/PR or RGB signals When inputting Y/PB/PR or RGB signals, you can input Y or G signals to connector 5, PB(B­Y) or B signals to connector 7 and PR(R­Y) or R signals to connector 9. When the cable is connected to connectors 6, 8 and 0, the 75-ohm termination of connectors 5, 7 and 9 is automatically released, and you can obtain loop-through output of the above signals from connectors 6, 8 and 0, respectively. Even if you do not wish to use loop-through output, you need not attach the 75-ohm termination to cconnectors 6, 8 and 0. Trap filter incorporated A trap filter incorporated into the BKM-128WX enables reducing noise produced when signals with a specific frequency range are displayed on an LCD monitor. 7 (E) BKM-128WX Analog Input Adaptor Input of EXT SYNC (external sync) signals To operate the monitor with the external sync signals, input the standard signals from an external sync generator, etc. You can obtain the loop-through output from connector !TM. To operate video equipment with the monitor by using the same sync signal, connect the external input connector of the video equipment to connector !TM. Even if you do not wish to use loop-through output, you need not attach the 75-ohm termination to connector !TM. The EXT SYNC signals do not function with analog composite/YC inputs. Signal characteristics Analog composite, YC signals Signal level Analog composite 1 Vp-p +3 dB/­6 dB YC Y: 1 Vp-p ±6 dB C: 0. 286 Vp-p ±6 dB (NTSC burst signal level) 0. 3 Vp-p ±6 dB (PAL burst signal level) Luminance signal Frequency characteristics Analog composite Monochrome signal: 50 Hz to 6 MHz ±2 dB Color signal: ­30 dB relative to subcarrier frequency YC Y: 50 Hz to 6 MHz ±2 dB Chrominance signals Demodulation axis R­Y/B­Y Subcarrier synchronization range ±200 Hz min. Chroma phase adjustment range (NTSC) ±10° min. Aperture compensation OFF : 0 dB ON : 2­6 dB (3MHz) Analog component (Y/PB/PR, RGB) signals Signal level Y/PB(B-Y)/PR(R­Y) Y: 1 Vp-p ±6 dB PB(B­Y): 0. 7 Vp-p ±6 dB PR(R­Y): 0. 7 Vp-p ±6 dB R/G/B 1 Vp-p ±6 dB (sync on G) Frequency characteristics Y 48 Hz to 30 MHz ±3 dB PB(B-Y)/PR(R­Y) 48 Hz to 30 MHz ±3 dB R/G/B 48 Hz to 30 MHz ±3 dB Return loss 40 dB min. (10 MHz) EXT SYNC (external sync) signals Signal level EXT SYNC 0. 3 to 8 Vp-p Return loss 40 dB min. (6 MHz) Specifications General Power requirements +5 V, ±6 V (supplied from the monitor) Power consumption 3 W Operating conditions Temperature 0°C to 35°C (32°F to 95°F) Optimum temperature 20°C to 30°C (68°F to 86°F) Humidity 0% to 90% (no condensation) Pressure 700 hPa to 1060 hPa Storage and transport conditions Temperature ­10°C to 40°C (14°F to 104°F) Humidity 0% to 90% Pressure 700 hPa to 1060 hPa Maximum external dimensions (w/h/d) 50 × 162 × 122 mm (2 × 61/2 × 47/8 inches) (2-slot size) Mass 470 g (1. 6 oz) Input/output connectors Analog composite signals BNC × 1, high impedance, with loop-through output and 75-ohm automatic termination YC signals 4-pin mini DIN × 1, with loop-through output and 75ohm automatic termination Y/PB/PR, RGB signals BNC × 3, high impedance, with loop-through output and 75-ohm automatic termination EXT SYNC signals BNC × 1, with loop-through output and 75-ohm automatic termination Accessories supplied Installation Manual (1) Design and specifications are subject to change without notice. 8 (E) BKM-129X Analog Component Input Adaptor The BKM-129X Analog Component Input Adaptor is a video signal input adaptor for Sony video monitors. [. . . ] 2 1 A 3 4 5 B Multiple connections There are three ways to connect equipment. Daisy chµconnection The equipment items are connected in series. · 17 or fewer equipment items including the monitor are connected. · The connection length is 72 m or less. Notes · The equipment cannot be operated if the equipment items are linked. Star type connection One item of equipment is connected to one connector on the monitor. · The cable can be disconnected with equipment turned on (hot plug function), but do not disconnect the plug while the date is being communicated. 16 (E) Troubleshooting If the problem persists after you attempted to correct the problem using the following, consult qualified Sony personnel. [. . . ]