User manual SONY BKM-41HD

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] When installed in the input option slots on the rear panel of the video monitor, they provide video input/ output connectors for the monitor. Using the Input and Output Connectors For information about installing the BKM-41HD/42HD in the video monitor input option slots, see "Installing into Video Monitors" on page 4(E). Functions Decoding of HD Serial Digital signals The built-in decoder decodes the HD serial digital signals. Configuration of Input/Output Connectors and Signals that may be Input The configuration of the input and output connectors and the signals that may be input are shown below. HD Serial Digital and Analog Input and Output Signal Connectors The BKM-41HD is equipped with one pair of input and output connectors for serial digital signals, as well as one pair of input and output connectors for analog signals. The BKM-42HD is equipped with two pairs of input and output connectors for serial digital signals, as well as one pair of input and output connectors for analog signals. On both the BKM-41HD and BKM-42HD, you can input one Y/PB/PR or one GBR signal using the analog input connectors. HD-SDI ANALOG 1 2 3 4 IN 1 MONITOR OUT IN 2 MONITOR OUT HD serial digital signals 5 6 7 8 IN Y/G OUT IN PB/B OUT Analog signals Available Signal Format (HD serial digital input) The following signal formats can be input to the HD SDI connector of the above models. The frame rate of the signal formats are also compatible with 1/1. 001. · 1080/24PsF1) · 1080/50I · 1035/60I2) · 1080/60I2) · 720/60P Note 9 0 IN PR/R OUT The above picture shows the BKM-42HD connectors. The connectors numbered 3, 4 are not equipped with the BKM-41HD. To have access to all of the above signal formats for the BVM-D20F1U/D24E1WU monitor, use the BKM41HD/42HD with a serial number from 2600001 to 2610000. 1) Input of HD serial digital signals You can input HD serial digital signals to connectors 1 and 3. You can obtain active loop-through output of each input from connectors 2 and 4 respectively. You need not attach 75-ohm terminators to connectors 2 and 4. 2) When the 1080/24PsF signal format is input, the monitor scanning mode is the 48 interlace (1080/48I). When the BKM-41HD or BKM-42HD are used for the HDM14E1, HDM-14E5, HDM-20E1 series monitor, only the 1035/ 60I and 1080/60I signal formats are available. 2(E) Notes Input/Output Connectors Digital input BKM-41HD: BNC × 1, with monitor output BKM-42HD: BNC × 2, with monitor output Both BKM-41HD and BKM42HD: BNC × 3, with loopthrough output · The MONITOR OUT signals are available only when the power of the video monitor is ON. The MONITOR OUT signals are not available when the monitor is in standby mode. · The MONITOR OUT signals do not satisfy the ONLINE signal specifications. Input of analog signals You can input a Y or G signal to connector 5, a PB or B signal to connector 7, a PR or R signal to connector 9. [. . . ] Le matériel contenu dans ce manuel consiste en informations qui sont la propriété de Sony Corporation et sont destinées exclusivement à l'usage des acquéreurs de l'équipement décrit dans ce manuel. Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des opérations ou entretiens de l'équipement à moins d'une permission écrite de Sony Corporation. [. . . ]