User manual SONY BKM-WE2000

[. . . ] NETWORK INTERFACE BOARD BKMW-E2000 !WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! [. . . ] (Proceed to Step 15. ) (3) Bend the harness (EPR-VN) of the supplied accessories as shown in the Fig. (4) Set the ferrite cores to the shield plate side, and tuck the harness between the boards. And then connect it to the connectors CN5 on the VN-13 board and CN2 on the IF-886 board. 2) n Be sure to open the space between the edge of the shield plate and the harness (EPR-VN) as shown in the figure. Fig. 1 Harness (EPR-VN) (Supplied accessory) 15. Arrange the coaxial cables as shown in the figure, and reattach the cable protector in the arrow direction. Cable protector 65 mm 10 mm 70 mm or EPR-1 board IF-886 board (When there is the coaxial cables disconnected. VN-13 board CN2 Fig. Reattach the upper lid (rear) assembly of the VTR, and tighten the two screws (with stopper). Harness (EPR-VN) VN-13 board Space Ferrite cores EPR-1 board Shield plate IF-886 board 1-12 (E) BKMW-E2000 1-2. (1) Loosen the screw (with stopper) completely. (2) Move the two knobs of the upper lid (front) assembly inwards. (To secure the upper lid (front) assembly, move the knob outwards. ) (3) Hold the back of the upper lid (front) assembly, and pull out in the arrow direction. Knob Upper lid (front) assembly 2. (1) Remove the left and right screws (one each) securing the front panel. (2) Push the left and right unlock buttons, and open the lower control panel as shown in the figure. (3) Unhook the two hooks at the bottom of the front panel. Hook PSW3 x 6 Unlock button Front panel Hook Screw with stopper Knob Lower control panel PSW 3x6 Unlock button (4) Release the two hooks and three claws from the chassis, and remove the front panel in the arrow direction. Removal Installation Front panel Claw Hook Claw Claw Hook BKMW-E2000 1-13 (E) 1-2. (1) Break the two claws A of the format escutcheon using the pliers, and remove them. (2) Release the three claws B from the front panel, and remove the format escutcheon in the arrow direction. 5. (1) Disconnect the harness from the connector CN1 on the LED-357 board. (2) Remove the two screws and remove the SWC-40 board. (3) Disconnect the harness (12 pin) from the connector CN1 on the SWC-40 board. LED-357 board Format escutcheon Harness (12 pin) CN1 Claw A SWC-40 board Claw A CN1 BVTT3 x 6 Claw B Front panel Claws B Format escutcheon 6. Disconnect the harness (9 pin) from the connector CN4 on the HP-101 board, and remove it. HP-101 board CN4 4. Attach the format escutcheon removed in step 3 to the front panel (E) for the BKMW-E2000, and snap on the three hooks as shown in the figure. NG Front panel (E) (for the BKMW-E2000) OK Hook Hook Harness (9 pin) CN4 HP-101 board Hooks Format escutcheon 1-14 (E) BKMW-E2000 1-2. (1) Connect the harness (HP-SW) of the supplied accessories to the connectors CN4 on the HP-101 board and CN2 on the SW-1106 board. (2) Connect the harness (12 pin) disconnected in (3) of step 5 to the connector CN1 on the SW-1106 board. [. . . ] (Example: Phone number etc. ) sysName: Generally used to enter the name of the system. (Example: "e-VTR-001" etc. ) sysLocation: Generally used to enter the name of the place that the system is located. (Example: "A-Studio" etc. ) To enable the settings Click the Execute button. The changed contents are stored in e-VTR even if the power is turned off. [. . . ]