User manual SONY BVM-14F5U

[. . . ] TRINITRON® COLOR VIDEO MONITOR BVM-14F5U/14F5E BVM-14E5U/14E5E OPERATION MANUAL [English] 1st Edition (Revised 1) Serial No. 2000001 and Higher WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: Danger of explosion if battery is incorrectly replaced. [. . . ] Simultaneously with the adjustment of the gain and bias, the 100 IRE and 20 IRE signals are automatically switched. When adjusting the gain and bias, input the proper signal. ADJUST. . . : Perform the adjustment with following knobs. ÷ 212 RED: CONTRAST knob (Adjust the R gain or bias with the CONTRAST knob. ) GREEN: BRIGHT knob (Adjust the G gain or bias with the BRIGHT knob. ) BLUE: CHROMA knob (Adjust the B gain or bias with the CHROMA knob. ) LUMINANCE: PHASE knob (Adjust luminance with the PHASE knob. ) 211 ORIGINAL VALUE: Select STD, COL1, COL2, or CH SET. ÷ 210 STD: Use common data (factory setting: D65). COL1: Use common data (factory setting: D65). COL2: Use common data (factory setting: D93). 212 ADJUST GAIN (STD/COL1/COL2/xxCH) (1/2): Adjust the gain with the proper knob. G:xxxx B:xxxx R:xxxx 212 ADJUST BIAS R:xxxx (STD/COL1/COL2/xxCH) (2/2): Adjust the bias with the proper knob. G:xxxx B:xxxx 26 220 PROBE (STD/COL1/COL2/xxCH): Select the probe for color temperature adjustment. SONY GRASEBY MINOLTA PHILIPS THOMA BKM-14L. . . : Use the BKM-14L. ÷ 230 SLS 9400. . . : Use the SLS 9400. ÷ 241 PM 5639. . . : Use the PM 5639. ÷ 241 · If you cannot execute an ADJUST or ANALYZE menu operation when using the Sony BKM-14L probe, try again after disconnecting and reconnecting the probe. · When using the Thoma TF6 probe, set the TF6 PRINT menu to off. 241 PROBE (STD/COL1/COL2/xxCH): Select the probe. Select either D65 or D93, and enter values for LOWLIGHT and HIGHLIGHT. Rather than selecting D65 or D93, you may instead enter the values of the CIE 1931 color system x and y coordinates. LOW LIGHT (20IRE): Enter the brightness (cd/m2) for low light. HIGH LIGHT (100IRE): Enter the brightness (cd/m2) for high light. ÷ 242 242 COLOR TEMP ADJ (STD/COL1/COL2/xxCH): Perform adjustment. SET PROBE ON CRT PRESS ENTER Adjustment starts when the probe is placed against the center of the screen and the ENTER button is pressed. 260 COPY (STD/COL1/COL2/xxCH): Select the source to be copied from. OTHER VALUE. . . : Copy data from another channel or from common data. ÷ 261 OTHER MONITOR. . . : Copy data from another monitor. ÷ 263 MEMORY CARD. . . : Copy data from a memory card. ÷ 266 261 OTHER VALUE (STD/COL1/COL2/xxCH): SET. ÷ Copy is carried out. Select STD, COL1, COL2, or CH STD: Copy common data (factory setting: D65). [. . . ] SLOT1 SLOT2 SLOT3 SLOT4 SLOT5 SLOT6 SLOT7 SLOT8 SLOT9 58 Selecting the Monitor to Control -- ADDRESS Menu When multiple monitors are connected by a serial remote connection, they can be controlled with a BVM-14F5U/14F5E/14E5U/14E5E. The ADDRESS menu is used to choose whether one particular monitor or monitor group will be controlled, or whether operations are to be performed on all monitors together. SINGLE: Control only a specified monitor. GROUP: Control only a specified monitor group. [. . . ]