User manual SONY CA901K

[. . . ] Überlassen Sie Wartungsarbeiten stets nur einem Fachmann. For the customers in Europe (for CA-901F) WARNING This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Pour les utilisateurs en Europe (pour CA-901F) AVERTISSEMENT Il s'agit d'un produit de Classe A. [. . . ] You can also use a portable lens (with extender) if you attach the supplied camera stabilizer to the camera mount. Seven-inch viewfinder You can use either the BVF-77/77CE seven-inch monochrome viewfinder. Use the cables supplied with this unit to connect the viewfinder. Functions for studio camera When you fit the camera with a studio lens and viewfinder to this unit you will be able to use the following functions suitable for studio shootings in addition to those for ENG and EFP: · You can perform a variety of operations from the rear panel, such as selecting whether or not you use the tally indicator and controlling the box cursor and marker displays in the viewfinder. · AC output connector (CA-901K: 120 V AC, CA901F: 220 or 240 V AC). · Script light connector (5 W) and on/off switch. 2(E) System Configuration An example configuration of a studio camera system using this unit is shown below. Triaxial cables are available to connect this unit and a CCU. Maximum cable lengths are as follows: Triaxial cable Fujikura (dia. 14. 5 mm) Belden 9232 Fujikura (dia. 8. 5 mm) Maximum lengtha) 3000 m (1800 m) 2250 m (1800 m) 1500 m (900 m) a) Figures in parentheses for use with video return function. VFH-770 outdoor viewfinder hood (available separately) BVF-77/77CE 7-inch monochrome viewfinder BVP-550 Color Video Camera CA-901K/901F Camera Build-Up Unit (this unit) Studio lens CA-550/550P Camera Adaptor CCT-K5T/K10T/K20T/K50T/K100T/K150T/K200T or CCT-5/ 10/20/50/100/150/200 triaxial cable (available separately) V-wedge shoe (supplied with tripod) CCU-700/700P Camera Control Unit Tripod Studio camera system configuration 3(E) Location and Function of Parts Lens Attachment Section (Front) and Connectors 1 2 4 Lens connector 2 5 CCU connector 6 CA connector Lens mouth Pushrod exit 1 Lens hold lever 2 Lens hold lever locking knob 7 AC OUT connector 3 Lens connector 1 Lens attachment section and connectors 1 1 Lens hold lever Holds the lens by the tongue-like protrusion at the lens bottom. 2 Lens hold lever locking knob Locks the lens hold lever 1. Turn clockwise to tighten, and counterclockwise to loosen. 3 Lens connector 1 (36-pin) Connect to the camera connector of the lens. 4 Lens connector 2 (12-pin) Connect to the LENS connector of the camera. 5 CCU (camera control unit) connector (triaxial connector, Kings type for the CA-901K, and Fischer type for the CA-901F) Connect to the CAMERA connector of the CCU with CCT-K5T/K10T/K20T/K50T/K100T/K150T/K200T (for CA-901K) or CCT-5/10/20/50/100/150/200 (for CA-901F) triaxial cable (available separately). 6 CA (camera adaptor) connector (triaxial connector, Kings type for the CA-901K, and Fischer type for the CA-901F) Connect to the CCU-550/550P connector of the CA550/550P camera adaptor. 7 AC OUT (AC power output) connector (3-pin) AC power supply (CA-901K: 120 V AC, CA-901F: 220 or 240 V AC) for external equipment is available via this connector. When using the AC OUT connector, see the section "Input/ output connectors" on page 20(E) for the maximum triaxial cable lengths for connection to the CCU connector. 4(E) Camera Mount Section (Inner Base) and Connectors 2 Carrying handle 5 Number plate holder 2 1 Camera mount 2 Slide lock knob 3 SCRIPT switch 4 SCRIPT connector Camera mount section and connectors 2 1 Camera mount (VCT-14 tripod attachment) Fit the camera. 2 Slide lock knob Locks the camera mount 1 so it does not slide. Turn counterclockwise to lock the camera mount at the far rear, and clockwise to lock it at the very front. 3 SCRIPT (script light) switch Turns the script light connected to the SCRIPT connector 4 on and off. 4 SCRIPT connector (4-pin) Supplies power (maximum 5 W) for a script light. 5 Number plate holder Fit the supplied number plates. 5(E) Location and Function of Parts Viewfinder Mount Section (Top) and Display Controls (Rear) 1 Viewfinder mount 2 VF connector 1 Pushrod hole 5 UP TALLY switch 3 VF connector 2 Power indicator 6 Box cursor control knob 4 CURSOR/MARKER switch Viewfinder mount section and display controls 1 Viewfinder mount Attach the viewfinder. 2 VF connector 1 (25-pin) Connect to the camera connector of the viewfinder. 3 VF connector 2 (12-pin) Connect to the VF connector of the camera, using the supplied viewfinder cables. 4 CURSOR/MARKER switch Turns the box cursor and markers in the viewfinder on and off. CURSOR ON, MARKER ON: Displays the box cursor, the safety zone marker, and the center marker. 5 UP TALLY switch Turn to ON if you want the viewfinder's exterior tally indicator to light when a tally signal is input (the tally indicator displayed on the viewfinder monitor screen cannot be controlled). 6 Box cursor control knobs Control the size and position of the box cursor displayed in the viewfinder. [. . . ] MARKER ON, CURSOR OFF: To display the safety zone marker and the center marker in the viewfinder screen. Use an internal switch of this unit to change the size of the safety zone to 80%. For more information, refer to the maintenance manual. Note Double markers will be displayed if you set the CURSOR/MARKER switch of this unit to ON while the camera's marker display setting is on. Be sure to set the camera's marker display to off. 19(E) Specifications General Mass 16. 5 kg (36 lb 60 oz) Dimensions (w/h/d) 260 × 413 × 522 mm (10 1/4 × 16 3/8 × 20 5/8 inches) 260 (10 1/4) Supplied accessories AC outlet plug (1) (CA-901F only) Operation and maintenance manual (1) Camera stabilizer (1) 3 /16 inch screws (2) L-wrench (for 3/16 inch screws, 1) Number plates (1 set) 413 (16 3/8) Accessories available separately CCT-K5T/K10T/K20T/K50T/K100T/K150T/K200T (for CA-901K) or CCT-5/10/20/50/100/150/200 (for CA-901F) triaxial cable BVF-77/77CE 7-inch monochrome viewfinder cable VFH-770 viewfinder hood CAC-6 return video selector 552 (20 5/8) 340 (13 1/2) Dimensions in mm (or inches) Operating temperature range ­20°C to +45°C (­4°F to +113°F) Storage temperature range ­20°C to +60°C (­4°F to +140°F) Related equipment BVP-550 Color Video Camera CA-550/550P Camera Adaptor CCU-700/700P Camera Control Unit RCP-7xx series Remote Control Panel Input/output connectors CCU connector (CA-901K: Kings triaxial connector, CA-901F: Fischer triaxial connector) Lens connector 1 (front) (36-pin) Lens connector 2 (with cable) (12-pin) VF connector 1 (rear top) (25-pin) VF connector 2 (rear bottom) (12-pin) CA connector (CA-901K: Kings triaxial connector, CA-901F: Fischer triaxial connector) AC OUT connector (3-pin)1) SCRIPT connector (4-pin) 1) When using the AC OUT connector, make sure the triaxial cable connected to the CCU connector is shorter than or equivalent to the following: Fujikura triaxial cable, 1200 m long (dia. 8. 5 mm) Design and specifications are subject to change without notice. 20(E) The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. [. . . ]