User manual SONY CCU-900 INSTALLATION MODEL

[. . . ] CAMERA CONTROL UNIT CCU-900 CCU-900P DIGITAL INTERFACE UNIT BKP-9330 INSTALLATION AND MAINTENANCE MANUAL 1st Edition (Revised 2) Serial No. 10001 and Higher: CCU-900 (UC) Serial No. 30001 and Higher: CCU-900 (J) Serial No. 40001 and Higher: CCU-900P (CE) Serial No. [. . . ] Rotary encoder Rotate : Moves the page or the item, or changes the set value. Push : Determines the page or enters the set value change mode. To move the page, rotate the rotary encoder. (Determined by pressing the rotary encoder. ) 3. To move the item, rotate the rotary encoder. (Determined by pressing the rotary encoder. ) n To enter the set value change mode, press the rotary encoder. To change the set value, rotate the rotary encoder. To end the setup menu, set the MENU ON/OFF switch to ON. CCU-900/900P IMM 2-1 (E) 2-2. Setup Menu Use this setup menu to set each signal line. Set data is stored in NV-RAM of the AT-122 board. To enter the setup menu, set the MENU ON/OFF switch to ON. 2-2-1. Contents of Setup Menu Setup Menu Entry Display * Setup Menu * >Return AUX PROMPT PIX Out WFM Out ColorBars Others Menu Return AUX PROMPT PIX Out WFM Out Color Bars Others Function Return video line setup AUX video line setup PROMPT video line setup PIX Out setup WFM Out setup Setup relevant to color bars Other setups 2-2 (E) CCU-900/900P IMM 2-2. Setup Menu Return Video Select Display * Return * >RET1 RET2 RET3 RET4 D-RET1 Active IN D-RET2 A-RET1 A-RET2 Item RET1 RET2 RET3 RET4 Setup D-RET1/2/3/4 AUX A-RET1/2/3/4 PROMPTER CAM Function Selects the signal to be assigned to each of RET1/2/3/4 when any of them is selected by the camera. The following signals can be selected for the RET1/2/3/4. CAM (CAMERA picture) ACTIVE display Indicates the line selected at the Camera side. Factory setting RET1 = A-RET1 RET2 = A-RET2 RET3 = D-RET1 RET4 = D-RET2 IN/NO display IN : When there are input signals NO : When there are no signals CCU-900/900P IMM 2-3 (E) 2-2. Setup Menu AUX Video Select Display * AUX * AUX >AUX1 AUX2 AUX3 AUX4 MATRIX ACTIVE D-RET1 Active NO D-RET2 A-RET1 A-RET2 Item Setup Function Sets the AUX video line. ACTIVE : Controls by CCU. Factory setting ACTIVE AUX MATRIX ACTIVE/ INACTIVE INACTIVE : Controls by MSU. When INACTIVE is set, follows the RET MATRIX setup of the MSU setup menu. AUX1 AUX2 AUX3 AUX4 D-RET1/2/3/4 AUX A-RET1/2/3/4 PROMPTER CAM Selects the signal to be assigned to each of AUX1/2/3/4 when any of them is selected by the CA-950/950P. The following signals can be selected for the AUX1/2/3/4 . CAM (CAMERA picture) AUX1 = A-RET1 AUX2 = A-RET2 AUX3 = D-RET1 AUX4 = D-RET2 ACTIVE display Indicates the line selected at the CA-950/950P side. When any of AUX1/2/3/4 is not selected by the CA-950/950P, the SERIAL AUX IN signal to the CCU-900/900P is selected as the signal of the AUX line. IN/NO display IN : When there are input signals NO : When there are no signals n When the dual mode is selected and set (in primary and secondary), the AUX Video line setup becomes invalid and the setup is fixed to the SERIAL AUX INPUT. 2-4 (E) CCU-900/900P IMM 2-2. Setup Menu Analog PROMPTER Select Display * Analog PROMPTER * >PROMPTER PROMPT IN Item Setup Function Selects a signal to be transmitted by the PROMPTER line. [. . . ] 12 16 : 9/4 : 3 SELECT EN IN 13 16 : 9/4 : 3 SELECT IN Specifications +5 V (OPEN) : DISABLE GND : ENABLE +5 V (OPEN) : 4 : 3 GND : 16 : 9 CCU-900/900P IMM 3-14 (E) Section 4 Service Overview 4-1. Cleaning of Connector/Cable Before connecting the unit to the camera adapter, it is recommended to clean the following optical contact portions. CCU connector of the camera adapter side . Optical/electrical cable Follow the procedures below for cleaning. [. . . ]