User manual SONY CD-BX10

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. [. . . ] If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. (RELEASE) 5 Setting the clock The clock has a 12-hour digital indication. Example: To set the clock to 10:08 CD Player Listening to a CD Insert a CD. Playback starts automatically. Label side up 1 Press (DSPL) during operation. If the POWER SELECT function is set to "ON, " go to step 2. If it is set to "OFF, " set to "ON" (page 9). Press (DSPL) for two seconds. 2 The hour indication flashes. 1 Set the hour. To go backward SOURCE To go forward If a CD is already inserted, press (SOURCE) repeatedly until "CD" appears to start playback. Elapsed playing time 2 Press (SOUND). Note To play back an 8 cm (3 in. ) CD, use the optional Sony compact disc single adapter (CSA-8). The minute indication flashes. To Stop playback Eject the CD Press 6 or (OFF) 6 3 Set the minute. To go backward SOURCE To go forward Changing the display item Each time you press (DSPL) during CD playback, the item changes as follows: z Elapsed playing time z Track number Clock Z 3 Press (DSPL). MOTION DISPLAY* Z * All the above items are scrolled in the display one by one in order. The clock starts. Note If the car has no accessory position on the ignition key switch, the clock cannot be set unless the power is turned on. Set the clock after you have turned on the radio, or started CD playback. 6 Locating a specific track -- Automatic Music Sensor (AMS) During playback, push the SEEK/AMS control up or down and release for each track you want to skip. To locate succeeding tracks To locate preceding tracks SEEK/AMS Radio Memorizing stations automatically -- Best Tuning Memory (BTM) This unit selects the stations with the strongest signals and memorizes them in the order of their frequencies. You can store up to 6 stations on each band (FM I, FM II, FM III, and AM). Locating a specific point in a track -- Manual Search During playback, push the SEEK/AMS control up or down and hold for about two seconds. Release when you have found the desired point. SEEK/AMS Caution When tuning in stations while driving, use Best Tuning Memory to prevent accidents. To search forward To search backward Note " or " " appears in the If " display, you have reached the beginning or the end of the disc and you cannot go any further. 1 Press (SOURCE) repeatedly to select the tuner. Each time you press (SOURCE), the mode changes as follows: CD ~ TUNER 2 Playing a CD in various modes Playing tracks repeatedly -- Repeat Play Press (1) during playback. You can store the bass and treble levels. Changing the sound and beep sound Boosting the bass sound -- D-bass You can enjoy a clear and powerful bass sound. The D-bass function boosts the low frequency signal with a sharper curve than conventional bass boost. You can hear the bass line more clearly even while the vocal remains at the same volume. You can emphasize and adjust the bass sound easily with the D-BASS control. This is similar in effect to an optional subwoofer system. Level D-BASS 3 D-BASS 2 D-BASS 1 1 Select the item you want to adjust by pressing (SOUND) repeatedly. BAS (bass) n TRE (treble) n BAL (left-right) n FAD (front-rear) n VOL (volume) 2 Adjust the selected item by rotating the dial. Adjust within three seconds after selecting the item. (After three seconds, the dial function reverts to volume control. ) 0dB Frequency (Hz) Adjusting the bass curve Turn the D-BASS control to adjust the bass level (1, 2, or 3). "D-BASS" appears in the display. To cancel, turn the control to OFF. Note If the bass sound becomes distorted, adjust the D-BASS control or volume. Turning on the clock display -- Power Select Function Only for cars with an accessory position on the ignition key switch To turn the Power Select Function ON Press (OFF) while pressing (SOUND). The Power Select Function ties the clock display power to the accessory position on the ignition key switch. [. . . ] 182 × 53 × 162 mm (7 1/4 × 2 1/8 × 6 1/2 in. ) (w/h/d) Approx. 10 oz. ) Parts for installation and connections (1 set) Front panel case (1) Cleaning cloth XP-CD1 Compact disc single adapter CSA-8 Tone controls Power requirements Dimensions Mounting dimensions Mass Supplied accessories Optional accessories * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block. Tuner section FM Tuning range Antenna terminal Intermediate frequency Usable sensitivity Selectivity Signal-to-noise ratio 87. 5 ­ 107. 9 MHz External antenna connector 10. 7 MHz 9 dBf 75 dB at 400 kHz 65 dB (stereo), 68 dB (mono) Harmonic distortion at 1 kHz 1. 0 % (stereo), 0. 7 % (mono) Separation 35 dB at 1 kHz Frequency response 30 ­ 15, 000 Hz Design and specifications are subject to change without notice. AM Tuning range Antenna terminal Intermediate frequency Sensitivity 530 ­ 1, 710 kHz External antenna connector 10. 71 MHz/450 kHz 30 µV Power amplifier section Speaker outputs (sure seal connectors) Speaker impedance 4 ­ 8 ohms Maximum power output 40 W × 4 (at 4 ohms) Outputs 12 Troubleshooting guide The following checklist will help you remedy the problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General Problem No sound. Cause/Solution ·Rotate the dial in a clockwise direction to adjust the volume. [. . . ]