User manual SONY CD-CX126

[. . . ] · Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctioning, or a safety hazard such as electrical shock or exposure of laser rays. · When your car was parked in direct sunlight resulting in a considerable rise in temperature inside the car, allow the unit to cool off before operating it. · Keep the volume at such a level that you can hear outside warning sounds (horns, sirens, etc. ). CAUTION! Invisible laser radiation when open and interlocks defeated. Avoid exposure to beam. ADVARSEL! Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. [. . . ] Care must be taken not to drop the panel. When the front panel is lifted from the unit, remove it by pulling away from the unit. LED lamp 3 Do NOT touch the connector on the reverse side of the front panel, as doing so may contaminate the connector and cause a poor connection resulting in a malfunction. ENGLISH 4 SETTING THE CLOCK RADIO OPERATION 1 2 Press PWR to turn the unit on. Press and hold DISP for more than 2 seconds. 1 2 Press PWR to turn the unit on. Press BAND to select the band from among FM1, FM2, FM3, MW1 (AM1), MW2 (AM2) and LW. The band indicators appear cyclically in order. · FM1, FM2 and FM3 share the same frequency range. · MW1 (AM1) and MW2 (AM2) share the same frequency range. 3 4 Press TUNE k to set the hour. Press DISP. The clock starts working from 0 second. Having the clock displayed while the unit is turned on Press DISP. To return the unit to its former display, press DISP again. The former display is restored after 5 seconds even if you don't press DISP. Band indicator Frequency indication 3 Press (more than 2 seconds) either TUNE k or TUNE i to tune in the desired station. The unit starts scanning and tunes in a station automatically (seek tuning). Press TUNE k to decrease and TUNE i to increase the frequency. Press the button again to cancel the function. Repeat the procedure until the desired station is tuned in. Note If you press (less than 0. 5 second at a time) either TUNE k or TUNE i, the frequency decreases or increases step by step. 4 Adjust the volume with +/-. 5 ENGLISH To turn the unit off Press PWR. PRESETTING STATIONS To preset stations automatically (auto memory) Note The "ST" (stereo) indicator lights up when the tuned-in station is broadcasting in stereo and the reception is good. 1 2 Press PWR to turn the unit on. Press BAND to select a desired band from among FM1, FM2, FM3, MW1 (AM1), MW2 (AM2) and LW. 3 Press and hold A. ME for more than 2 seconds to activate the automatic presetting function. This unit can store up to 6 stations in memory for the preset station buttons 1 to 6 with "LO" (local) indicator lighting up. If the unit could not search for all of 6 stations, "LO" (local) indicator goes off and starts searching for weaker stations again. Use this function to automatically preset up to 6 stations each for FM1, FM2, FM3, MW1 (AM1), MW2 (AM2) and LW (up to a total of 36 stations). · When auto memory is completed, the station stored in the preset station button 1 is tuned in. · To stop auto memory, press A. ME again. To check the preset stations (preset scan) · If you wish to check the preset stations, press A. ME for less than 2 seconds. The preset stations stored in memory will be tuned in for 5 seconds each in order. · To stop this function, press A. ME again or press any of the preset station buttons 1 to 6. continued ENGLISH 6 PRESETTING STATIONS To tune in the preset stations To preset stations manually You can manually preset stations that have not been selected by auto memory. 1 2 3 1 2 3 4 Press PWR to turn the unit on. Press BAND to select the band from among FM1, FM2, FM3, MW1 (AM1), MW2 (AM2) and LW. Tune in the station that you wish to preset with TUNE k or TUNE i. Press one of the preset station buttons 1 to 6 for approximately 2 seconds. While the station you are presetting is being registered in memory, the sound is momentarily muted. The number of the pressed preset station button appears next to the frequency indication. Press PWR to turn the unit on. [. . . ] Press TAPE/MD IN to listen to the connected equipment. The "TAPE" indicator lights up. · For further information on the portable cassette/ MD player, etc. , refer to the operating instructions for the equipment. With the unit off, press 1 and 4 at the same time. The "bEEP" indication appears. Each time you press them, this function turns on or off. The beep function is activated when the "bEEP" indication appears with the audio control indicator lighting up and canceled without the indicator. Audio control indicator ENGLISH 12 TROUBLESHOOTING Reset button The Reset button is visible when you detach the front panel. [. . . ]