User manual SONY CD-CX217

[. . . ] · Keep the volume at a level at which you can hear outside warning sounds (horns, sirens, etc. ). TABLE OF CONTENTS THEFT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 BASIC OPERATION, AUDIO AND CLOCK ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RADIO OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CD PLAYER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The unit also turns on when you insert a CD. · Press and hold PWR/MUTE until the unit turns off. Note Attaching the front panel 1 Engage the left side of the front panel to the left catch on the unit. Most operations described in this manual require the unit to be turned on before starting the operation, unless explicitly stated otherwise. Changing the source mode 1 Press FNC. Pressing FNC cycles through source modes in the following order: 2 Push the panel forward until it locks. Be sure not to press any buttons while you are attaching the panel. * "CD" does not appear in the display when there is no CD in the unit. Adjusting the volume Note Do not touch the front panel connector. This could cause a poor or faulty connection. 1 Turn the Smart Jog. VOL (volume) indicator flashes. Muting the sound Security lamp The security lamp will continue to flash while the front panel is detached from the unit. 1 Press PWR/MUTE briefly. To restore volume, briefly press PWR/MUTE again. ENGLISH 2 Adjusting sound You can select the following modes for adjusting sound depending on the music you listen to: BASS (low frequencies), TRE (high frequencies), BAL (left/right), FAD (front/ rear) and H-BASS (high bass) Setting the clock 1 Press and hold DISP until the clock indicator flashes in the display. 2 Press TUNEi (to set hour) or TUNEk (to set minute) and turn the Smart Jog. 1 Press SEL repeatedly to select the mode to be adjusted. The selected mode's indicator flashes. 2 Turn the Smart Jog to increase or decrease the level for the selected mode (except for H-BASS). In H-BASS mode, turn the Smart Jog to select on or off. 3 Press DISP. Displaying the clock 1 Press DISP. To return to the former display, press DISP again. Note Adjust the level or select on/off within 5 seconds, or the selected mode will return to previous state. RADIO OPERATION Tuning in to a station (Seek/Manual Tuning) Aligning the source levels (Source Level Adjuster) Volume may vary each time you change the source mode. In this case, you can align each source mode's volume to almost the same level. 1 Press FNC repeatedly to select the desired mode. "LA 0" appears in the display. 3 Turn the Smart Jog to adjust the level. Stereo indicator Local indicator Note Adjust the level within 5 seconds, or the selected mode will be canceled. Restoring the factory settings 1 Turn off the unit. 2 Press and hold DISP until "LA --" appears in the display. Band indicator Frequency indication 1 Press FNC repeatedly to select the desired band (FM1, FM2, FM3, AM1 or AM2). 2* Press TUNEi (to move to higher frequencies) or TUNEk (to move to lower frequencies) to tune in to a station. "ST" appears in the display when a station is broadcasting in stereo, and receiving conditions are good. *Seek Tuning and Manual Tuning · Press and hold TUNEi or TUNEk until seek Tuning starts. The unit locates a station automatically (Seek Tuning). · Press TUNEi or TUNEk repeatedly to search for a desired station while increasing or decreasing the frequency step by step (Manual Tuning). To stop Seek Tuning, press TUNEi or TUNEk again. Note You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, and H-BASS, and aligned source volume levels. Muting button beep sounds 1 Turn off the unit. 2 Press and hold SEL until "bEEP" appears in the display. 3 Turn the Smart Jog to select on (level indicators appear) or off (level indicators disappear). 4 Press and hold SEL until the unit turns off. Monaural mode When signals become weak, or reception becomes poor, the unit automatically switches to Monaural mode to reduce noise. 3 ENGLISH Local mode Local mode allows you to tune in only to strong stations during Seek Tuning. [. . . ] · A CD-R or CD-RW may take some time to start playing back, but this is not a malfunction. · If a CD-R or CD-RW with no data or incompatible data is inserted, "E03" will appear in the display. Reset button OTHER FUNCTIONS MAINTENANCE Cleaning the front panel Wipe the surface with a soft, dry cloth. Smart Jog Cleaning the connector The connector needs to be cleaned occasionally. [. . . ]