User manual SONY CD-CX237

[. . . ] · Keep the volume at a level at which you can hear outside warning sounds (horns, sirens, etc. ). TABLE OF CONTENTS THEFT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 BASIC OPERATION, AUDIO AND CLOCK ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RADIO OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CD PLAYER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The unit also turns on when you insert a CD. · Press and hold PWR/ATT until the unit turns off. Note Attaching the front panel 1 Engage the left side of the front panel to the left catch on the unit. Most operations described in this manual require the unit to be turned on before starting the operation, unless explicitly stated otherwise. 2 Push the panel forward until it locks. Be sure not to press any buttons while you are attaching the panel. Changing the source mode 1 Press Jog dial (PUSH-SOURCE). Pressing Jog dial (PUSH-SOURCE) cycles through source modes in the following order: TUNER (FM1/FM2/FM3/AM1/AM2) CD* AUX * "CD" does not appear in the display when there is no CD in the unit. Adjusting the volume Note Do not touch the connector on the reverse side of the front panel. This could cause a poor or faulty connection. 1 Turn Jog dial. VOLUME indicator appears. Muting the sound 1 Press PWR/ATT briefly. ATT indicator flashes. To restore volume, briefly press PWR/ATT again. ENGLISH 2 Adjusting sound You can select the following modes for adjusting sound depending on the music you listen to: BASS (low frequencies), TRE (high frequencies), BAL (left/right), FAD (front/ rear) and H-BASS (high bass). Setting the clock 1 Press and hold DSPL until the clock indicator flashes on the display. 2 Press + (to set hour) or ­ (to set minute), and then turn Jog dial. 1 Press SEL repeatedly to select the mode to be adjusted. The selected mode's indicator appears. 2 Turn Jog dial to increase/decrease the level or to select on/off for the selected mode. 3 Press DSPL. Displaying the clock 1 Press DSPL. To return to the former display, press DSPL again. Note Adjust the level or select on/off within 5 seconds, or the selected mode will return to previous state. RADIO OPERATION Tuning in to a station (Seek/Manual Tuning) LO Aligning the source levels (Source Level Adjuster) Volume may vary each time you change the source mode. In this case, you can align each source mode's volume to almost the same level. 1 Press Jog dial (PUSH-SOURCE) or TU (TUNER) repeatedly to select the desired mode. "LA 0" appears on the display. 3 Turn Jog dial to adjust the level. +/­ TU (TUNER) Local indicator Stereo indicator Note Adjust the level within 5 seconds, or the selected mode will be canceled. Restoring the factory settings 1 Turn off the unit. 2 Press and hold DSPL until "LA --" appears on the display. Band indicator Frequency indication TUNER indicator 1 Press TU (TUNER) repeatedly to select the desired band (FM1, FM2, FM3, AM1, or AM2). Note You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, and H-BASS, and aligned source volume levels. 2* Press + (to move to higher frequencies) or ­ (to move to lower frequencies) to tune in to a station. "STEREO" appears on the display when an FM station is broadcasting in stereo, and receiving conditions are good. *Seek Tuning and Manual Tuning · Press and hold + or ­ until seek Tuning starts. The unit locates a station automatically (Seek Tuning). · Press + or ­ repeatedly to search for a desired station while increasing or decreasing the frequency step by step (Manual Tuning). To stop Seek Tuning, press + or ­ again. Setting the beep tone 1 Turn off the unit. 2 Press and hold SEL until "bEEP" appears on the display. 3 Turn Jog dial to select on (level indicators appear) or off (level indicators disappear). 4 Press SEL. 3 ENGLISH Monaural mode When signals become weak, or FM reception becomes poor, the unit automatically switches to Monaural mode to reduce noise. Presetting stations manually (Manual Memory) 1 Press TU (TUNER) repeatedly to select the desired band (FM1, FM2, FM3, AM1, or AM2). Local mode Local mode allows you to tune in only to strong stations during Seek Tuning. 1 Press LO before you start seek tuning. "LOCAL" appears on the display. [. . . ] You must pick up the product when warranty performance is completed or, if you choose, and the product was received by the Service Center during the LABOR warranty period, the repaired product will be returned to you freight prepaid. You must present to the Service Center, or include with your shipment, a dealer's bill of sale, or other original evidence, showing the date and place of purchase and describing the product purchased. Be sure to include your return address and daytime telephone number where you can be reached should the need arise. WHAT THE WARRANTY DOES NOT COVER This warranty does not cover (1) products purchased outside of the U. S. A. ; (2) product set-up, adjustment of controls, repair of antenna systems outside the unit; (3) removal or reinstallation, batteries, carrying case, AC adapters and other accessories packaged with the product; (4) defects occurring after purchase due to repair or service other than by an Aiwa Authorized Service Center, product modification, accident, misuse, abuse, or negligence; or (5) reception problems caused by signal conditions, or cable or antenna systems outside the unit. This warranty will not apply if the serial number of the unit has been altered or removed. REPAIR OR REPLACEMENT AS PROVIDED IN THIS WARRANTY IS THE PURCHASER'S EXCLUSIVE WARRANTY REMEDY. [. . . ]