User manual SONY CD-CZ117

[. . . ] · Keep the volume at a level at which you can hear outside warning sounds (horns, sirens, etc. ). TABLE OF CONTENTS BASIC OPERATION, AUDIO AND CLOCK ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RADIO OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CD PLAYER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 AUXILIARY EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The unit also turns on when you insert a CD. · Press and hold PWR/MUTE until the unit turns off. Adjust the level or select on/off within 5 seconds, or the selected mode will return to previous state. Aligning the source levels (Source Level Adjuster) Volume may vary each time you change the source mode. In this case, you can align each source mode's volume to almost the same level. 1 Press FNC repeatedly to select the desired mode. "LA 0" appears in the display. 3 Turn the Smart Jog to adjust the level. Note Most operations described in this manual require the unit to be turned on before starting the operation, unless explicitly stated otherwise. Changing the source mode 1 Press FNC. Pressing FNC cycles through source modes in the following order: Note Adjust the level within 5 seconds, or the selected mode will be canceled. Restoring the factory settings * "CD" does not appear in the display when there is no CD in the unit. 1 Turn off the unit. 2 Press and hold DISP until "LA --" appears in the display. Adjusting the volume 1 Turn the Smart Jog. VOL (volume) indicator flashes. Note You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, and H-BASS, and aligned source volume levels. Muting the sound 1 Press PWR/MUTE briefly. To restore volume, briefly press PWR/MUTE again. Muting button beep sounds 1 Turn off the unit. 2 Press and hold SEL until "bEEP" appears in the display. 3 Turn the Smart Jog to select on (level indicators appear) or off (level indicators disappear). 4 Press and hold SEL until the unit turns off. ENGLISH 2 Setting the clock 1 Press and hold DISP until the clock indicator flashes in the display. Monaural mode When signals become weak, or reception becomes poor, the unit automatically switches to Monaural mode to reduce noise. 2 Press TUNEi (to set hour) or TUNEk (to set minute) and turn the Smart Jog. Local mode Local mode allows you to tune in only to strong stations during Seek Tuning. 1 Press LO before you start seek tuning. To return to Distant mode, press LO again. "LO" disappears and the unit tunes in to all receivable stations. 3 Press DISP. Displaying the clock 1 Press DISP. To return to the former display, press DISP again. RADIO OPERATION Tuning in to a station (Seek/Manual Tuning) Using preset stations You must preset stations before you can tune in a station using preset station number buttons. Preset station buttons 1 ~ 6 Stereo indicator Local indicator Preset station number Band indicator Frequency indication Presetting stations automatically (Auto Memory) 1 Press FNC repeatedly to select the desired band (FM1, FM2, FM3, AM1 or AM2). 2* Press TUNEi (to move to higher frequencies) or TUNEk (to move to lower frequencies) to tune in to a station. "ST" appears in the display when a station is broadcasting in stereo, and receiving conditions are good. *Seek Tuning and Manual Tuning · Press and hold TUNEi or TUNEk until seek Tuning starts. The unit locates a station automatically (Seek Tuning). · Press TUNEi or TUNEk repeatedly to search for a desired station while increasing or decreasing the frequency step by step (Manual Tuning). To stop Seek Tuning, press TUNEi or TUNEk again. 1 Press FNC repeatedly to select the desired band (FM1, FM2, FM3, AM1 or AM2). 2 Press and hold PS/A. ME until automatic presetting starts. The unit automatically stores up to 6 stations for each band. [. . . ] "REPEAT1" appears in the display. To cancel One track Repeat Play, press REP1 again. Random Play 1 Insert a CD. "CD" appears in the display. If a CD is already inserted, press FNC repeatedly to select CD play mode. In normal play, when the last track finishes, the unit returns to the first track and continues to play. [. . . ]