User manual SONY CD-CZ127

[. . . ] · Keep the volume at a level at which you can hear outside warning sounds (horns, sirens, etc. ). TABLE OF CONTENTS BASIC OPERATION, AUDIO AND CLOCK ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RADIO OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CD PLAYER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AUXILIARY EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2 Turn AUDIO CONTROL to increase/decrease the level or to select on/off for the selected mode. Note Adjust the level or select on/off within 5 seconds, or the selected mode will return to previous state. Aligning the source levels (Source Level Adjuster) i/k DISP SRC BAND Volume may vary each time you change the source mode. In this case, you can align each source mode's volume to almost the same level. 1 Press SRC or BAND repeatedly to select the desired mode. "LA 0" appears in the display. 3 Turn AUDIO CONTROL to adjust the level. Turning the unit on/off · Press PWR/MUTE to turn on the unit. The unit also turns on when you insert a CD. · Press and hold PWR/MUTE until the unit turns off. Note Most operations described in this manual require the unit to be turned on before starting the operation, unless explicitly stated otherwise. Note Adjust the level within 5 seconds, or the selected mode will be canceled. Changing the source mode 1 Press SRC. Pressing SRC cycles through source modes in the following order: Restoring the factory settings 1 Turn off the unit. 2 Press and hold DISP until "LA --" appears in the display. ENGLISH FM1 (FM2/FM3/AM1/AM2) CD* AUX * "CD" does not appear in the display when there is no CD in the unit. Note You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, and H-BASS, and aligned source volume levels. Adjusting the volume 1 Turn AUDIO CONTROL. VOL (volume) indicator flashes. Muting button beep sounds 1 Turn off the unit. 2 Press and hold SEL until "bEEP" appears in the display. Muting the sound 1 Press PWR/MUTE briefly. MUTE indicator flashes. To restore volume, briefly press PWR/MUTE again. 3 Turn AUDIO CONTROL to select on (level indicators appear) or off (level indicators disappear). 4 Press SEL. Adjusting sound You can select the following modes for adjusting sound depending on the music you listen to: BASS (low frequencies), TRE (high frequencies), BAL (left/right), FAD (front/ rear) and H-BASS (high bass). ENGLISH 2 Setting the clock 1 Press and hold DISP until the clock indicator flashes in the display. 2 Press i (to set hour) or k (to set minute), and then turn AUDIO CONTROL. 3 Press DISP. Monaural mode When signals become weak, or reception becomes poor, the unit automatically switches to Monaural mode to reduce noise. Local mode Local mode allows you to tune in only to strong stations during Seek Tuning. 1 Press LO before you start seek tuning. To return to Distant mode, press LO again. "LO" disappears and the unit tunes in to all receivable stations. Displaying the clock 1 Press DISP. To return to the former display, press DISP again. RADIO OPERATION Tuning in to a station (Seek/Manual Tuning) LO Using preset stations You must preset stations before you can tune in a station using preset station number buttons. PS/A. ME i/k BAND i/k BAND Stereo indicator Local indicator Preset station buttons 1 to 6 Preset station number Band indicator Frequency indication Presetting stations automatically (Auto Memory) 1 Press BAND repeatedly to select the desired band (FM1, FM2, FM3, AM1, or AM2). 1 Press BAND repeatedly to select the desired band (FM1, FM2, FM3, AM1, or AM2). 2* Press i (to move to higher frequencies) or k (to move to lower frequencies) to tune in to a station. "ST" appears in the display when an FM station is broadcasting in stereo, and receiving conditions are good. *Seek Tuning and Manual Tuning · Press and hold i or k until seek Tuning starts. The unit locates a station automatically (Seek Tuning). · Press i or k repeatedly to search for a desired station while increasing or decreasing the frequency step by step (Manual Tuning). [. . . ] If the error code indication does not disappear, consult an AIWA service center. Check that the CD is loaded properly (right side up, etc. ), and the CD contains valid data. Note During Random Play, pressing r allows you to skip only to the beginning of the current track, not to the previous track. AUXILIARY EQUIPMENT Listening to a cassette/MD/MP3 portable player or other equipment You can listen to equipment connected to the unit. Refer to the operating instructions for the corresponding equipment for more detailed information. Be sure to remove inserted CDs to prevent possible damage to the unit before connecting the equipment. Reset button If a CD does not operate properly, press the reset button with a pointed object such as a pencil, etc. [. . . ]