User manual SONY CDP-LSA1

[. . . ] ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. Welcome! Thank you for purchasing the Sony Compact Disc Player. Before operating the unit, please read this manual thoroughly and retain it for future reference. CAUTION You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment. About This Manual The instructions in this manual are for model CDP-LSA1. Owner's Record The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. [. . . ] Press /± repeatedly to input the first character. Input character Selecting a disc on the player Turn the JOG dial until the disc number or Disc Memo (see page 17) you want appears in the display. Press ENTER to start play. ALL DISC S S Symphony No1 CD1 Selecting a disc directly using the remote 1 Press DISC/CAPS. 2 Press the number button of the disc. Example: To enter number 35 Press 3, then 5. To enter number 100 Press 1, then 0 twice. Each time you press /±, the characters appear in the following order. ABCDEFGHIJKLMNOPQRSTUVWX YZ0123456789 If "NOT FOUND" appears in the display while inputting the first character with the /± buttons, no disc has been labeled using the input character. 3 Press ENTER to start play. (Continued) 11 Playing CDs Notes · When searching input characters, blanks and symbols before the first character in the Disc Memo are ignored. · When searching input characters, upper and lower cases cannot be differentiated. Locating a Specific Track or a Point in a Track You can quickly locate any track while playing a disc using the /± (AMS: Automatic Music Sensor) buttons or number buttons on the remote. You can also locate a specific point in a track while playing a disc. 3 Turn the JOG dial to find the disc you want. As you turn the JOG dial, the Disc Memos starting with the input character appear in the display. In Program Play mode, the disc will be added to the end of the program. 4 To cancel Memo Search Press MEMO SEARCH again. If there is no more Disc Memo starting with the input character in Step 3 The input character changes to the next one when you turn the JOG dial. /± Specifying the Next Disc to Play You can specify the next disc to play while playing a disc in Continuous or 1 DISC Shuffle Play mode. Therefore, if you want to start ALL DISCS Shuffle Play again from the beginning, be sure to repeat the procedure from Step 1. 2O *DISC-2O* 3 To program a whole disc, skip this step. Press /± until the track number you want appears in the display. CD1 PROGRAM1 DISC TRACK 2O 3 Track number 2O 1 STEP Creating Your Own Program (Program Play) You can arrange the order of the tracks and/or discs to create three different programs and programs are stored automatically. A program can contain up to 32 "steps" -- one "step" may contain a track or a whole disc. You can make programs using the controls on the remote as well as ones on the player. However, the programming procedures are different. 4 Press ENTER or PROGRAM. The track being programmed CD1 PROGRAM1 DISC TRACK 2O The disc being programmed 3 2O 1 STEP Playing order 5 Creating a program on the player PROGRAM /± ENTER JOG To program other discs/tracks, do the following: To program Other discs Other tracks on the same disc Other tracks on other discs Repeat Steps 2 and 4 3 and 4 2 to 4 6 Press · to start Program Play. To cancel Program Play Press CONTINUE. · CHECK CLEAR 14 Getting Started Playing CDs The programs remain even after Program Play ends When you press ·, you can play the same program again. 3 Press the number button of the disc. PROGRAM1 When you press PROGRAM during Continuous or Shuffle Play The program will be played after the current track. 2O DISC-[ 2O] CD1 4 To program a whole disc, skip this step and go to Step 6. Press TRACK/SPACE. PROGRAM1 The programs remain until you erase them If you replace discs, the programmed disc and track numbers remain. So, the player plays only the existing disc and track numbers. However, the disc and track numbers that are not found in the player or on the disc are deleted from the program, and the rest of the program is played in the programmed order. 2O TRACK-[ _] CD1 5 Press the number button of the track. PROGRAM1 Creating a program using the remote Z 2O TRACK-[ 3] CD1 6 Press ENTER. The disc being programmed CD1 TRACK/SPACE DISC/CAPS PROGRAM PROGRAM1 DISC TRACK 2O Number buttons ENTER 3 2O 1 STEP The track being programmed Playing order 7 To program other discs/tracks, do the following: To program Other discs Other tracks on the same disc CHECK · CLEAR Repeat Steps 2, 3 and 6 4 to 6 2 to 6 1 2 Press PROGRAM until the program number you want (PROGRAM 1, 2 or 3) appears in the display. Press DISC/CAPS. CD1 PROGRAM1 Other tracks on other discs 8 Press · to start Program Play. DISC-[ 20 _] To cancel Program Play Press CONTINUE. 15 Playing CDs Checking the programmed order You can check your program before or after you start playing. Each time you press this button, the display shows the disc and track number of each step in the programmed order. [. . . ] · If you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. · AC power cord must be changed only at the qualified service shop. Not this way · Do not expose the disc to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be considerable rise in temperature inside the car. · After removing a disc from the disc slot, store the disc in its case. On placement · Place the player in a location with adequate ventilation to prevent heat build-up in the player. [. . . ]